ETS22XBMBRCC General Electric Refrigerator - Instructions

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Had friend assist in pulling fridge out from it's area so that I could access back. Unplugged unit. For the bottom freezer units (mine) the compartment containing the main control board is middle of the fridge and on the left. Took off the protective metal plate and then followed the video demonstrating the repair. One other discrepancy between the video and the instructions that came with the new main control board, is that the instructions suggested locating and cutting some other green wire to the compressor unit. I chose not to do that, as the unit was otherwise working fine as is prior to my main control board going south.

replaced main board.

1. Pulled refrigerator out
2. Unpluged the refrigerator
3. Removed the three screws holding the cover on.
4. Removed Board ASM Main Control.
5. Unpluged Connector's.
6. Pluged Connector's in to new Board ASM Main Control.
7. Put cover back on.
8. Pluged refrigerator back in.
9. Pushed refrigerator back into place.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Removed 2 screws and removed the old slide. Installed new slide and 2 screws . Done.

Tom Paone at quality@applianceeducator.com. was very helpful at recommending that a solution to my problem was to replace the ASM Main Domestic Motherboard. I ordered and received the board in two days from PartSelect. After unplugging the refrigerator I used a nut driver to remove the three screws that held the motherboard cover in place and then disconnected all of the connections to the board. Next, using a pair of needle nose pliers, I gently squeezed on the white plastic anchor retainers that fastened the motherboard to the refrigerator. While doing this at each anchor I gently pulled on the motherboard until it was separated from the retainer anchor post. There were four retainers total. I removed the old board and in the reverse order installed the new board. All of the connectors were easy to match to the new board because the wiring connectors coming out of the back of the refrigerator were only long enough to hook to the correct connectors on the circuit board. There was an extra connector that I didn't use on the new board and also the connection for the ground wire used a ring connector instead of a spade connector. To remedy this I simply used the ground wire assembly from my old board. I also took the time to remove the lower cover on my refrigerator and cleaned the condensing coil with a vacuum cleaner. The total time to replace the motherboard and clean the condensing coil was about 20 minutes from start to finish. This repair solved the problem with my evaporator fan. A big thanks to Tom Paone at quality@applianceeducator.com. for helping diagnosis my problem and suggesting the correct replacement part. I saved between $100.00 to $150.00 not having to call out an appliance repair person to fix my refrigerator.

It was a very simple installation after reading about everyone else having the same "noise" problem with their GE side by side refrigerator.

I simply; pulled the refrigerator out, turned off the power, took off the 3 screws to remove the plate, unhooked the 5 or so connections with my hands, put the new part in, hooked the connections up, put the plate back on, plugged the refrigerator back in, and slid in back into place. It took around 10 minutes to do, very simple.

i Removed back panels and then I removed the faulty circuit board. Installed new circuit board and presto everything worked. I can't believe how easy it was but on the other hand I couldn't believe a refrigerator had such a sophisticated part..

removed 6 screws and repaced cover.

Followed the partselect video on how to replace motherboard and the video described the exact replacement procedure.

Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.

You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.

Removed the old control board at the rear of the refigerator, installed the replacement board.

narrowed it down to the circuit board...removed cover panel after unplugging frig. read directions thouroughly.... removed cables attached to old board. this is the tricky part removing the board from the plastic clips....broke two pulling old board off popped new Board onto remaining plastic mounting clips and reattached cables plugged frig in and got a shock as my shoulder touched the board. everything seemed to be working and but cover back on....viola all done.