MSG20GWBEWW General Electric Refrigerator - Instructions

I took the glass plate off the top of the drawer, then removed the draw. I then removed the two screws holding the slide rail. I put the new slide rail in place, put the screws back in it, slide the drawer back in place and replaced the glass top. nothing to it.

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

It seems my refrigerator was old enough [1987] that the spacing on the holes for the bracket were different than the part that is currently sold. The holes on the new bracket were 30 mm apart on center, but on the old bracket they were 20 mm apart on center.

Clamped the old and new brackets together in a vise to use the old bracket for spacing and drilled a new hole through the 4mm of steel.

After which it was a snap installing the new hinge assembly.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

Opened, discovered not flapper but more complicated

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

the previous left behind a side by side, everything worked however the auger in the ice bucket was a little rusty. I wish that I could say it was all me but the truth of the matter was the videos on file.

They were nicely done and easy to follow as I took the unit apart and replaced the auger in about 30 minutes. Thanks for all your help in part look up.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

Unplugged the refrigerator then used the cordless drill to remove the 6 screws on the access panel on the back of the fridge to be able to get to the fan. Was able to pull the fan off by hand and push the new fan on by hand. Plugged the refrigerator by in and watched the fan run for a few minutes then replaced the access panel. Really quick and easy repair.

Removed 2 screws replaced new part very easy

took 2 philips screws out,took off rail,and then nreverse.these steps,

Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes

First I removed glass shelf on top of rail. I then removed the two screws holding rail to refrigerator side. Next I installed new rail using same two screws. Finally I replaced glass shelf on top of rail.