TFJ22JABGAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mike from Alpharetta, GA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
door would not close by itself - broke cam riser
My right door (food door on side-by-side) stopped closing - I found pieces of the plastic washer (cam riser) on the floor. After reading the stories on the web I decided to order the new part - and YES there are many universal parts that work for Kenmore/GE. The part comes with two parts (hinge and cam riser) - you should install both to insure a good fit. I took 3 blocks of wood and a shim and supported the bottom center of the door, unscrewed the hinge off and dropped it out (3 minutes). The "only" tough part was unscrewing the cam riser from the bottom of the door - it required a very small socket and you will only have about 6-8 inches of work space. Be sure you have a socket that fits before you take the hinge off. The entire repair took less than 30 minutes and contrary to some of the posts, you DO NOT need to take the door off. Good as new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- danny from colorado springs, CO
- Parts Used:
- WR51X10101
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
freezer anf refrigerator got warm on both sides. Seemed like there was no air flow.
Parts select sugested checking the freezer side on the side by side if there was frost on the back panel. I took the back panel off on the freezer side inside the freezer. I found that the freezer coils were full of ice.Had to use a hair dryer to melt all the ice. The heater element was bad on the bottom of the freezer. I ordered a new defrost element an installed in 40 minutes and is running fine.You can still use the refrigerator until the new part comes in if you melt off the coils.It will last about 2 weeks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Kingman, AZ
- Parts Used:
- WR51X10101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Refrigerator and freezer not getting cold enough.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from GREENEVILLE, TN
- Parts Used:
- WR51X10101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Fridge not cooling, freezer icing up
This fridge had this same problem 4 other times, each time about 1 yr apart. Being as I considered myself ''mechanically challenged'' my wife always contacted her favorite appliance repair man. However, he was unavailable, so wife was gearing up to go ahead, bite the bullet, and buy a new fridge. We really didn't want another bill to worry with so she suggested I try the repair myself. She'd watched the repairman do it the last couple of times and ensured me it would be ''a piece of cake'' plus save us some bucks and put off an added expense at least a little longer. Ordering the part from this site was simple. The fridge did have the old 1 bulb element and the new one was the 2 bulb element so I was afraid I'd have to do some splicing, but lucked out and the wire was easily redirected and reached without any stress or problems to plug into the new part. She watched the install video and was able to talk me through it without any problems. We saved at least $125 install bill, plus put off making a big item purchase a while longer. I hope the new 2 element defroster does a better job and we might just get 10 more years out of 'old faithful'!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Cordova, TN
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door not closing properly
I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Naples, FL
- Parts Used:
- WR51X10101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refrigerator would not cool
I followed the easy instructions included with the replacement part I ordered. I removed the back of the freezer, unpluged the broken heater and replace with the new heater. The heater just plugged in, very very simple. I put the back panel bach on with the two screws and it perfectly. Not back for a girl!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Linesville, PA
- Parts Used:
- WR51X10101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator side of refrigerator/freezer wouldn't stay cool. Ice jam in cooling cools (due to burned out defrost heater) prevented proper air flow.
Removed shelves and light bulb cover. Then removed the two screws that hold the back wall of freezer compartment in place and removed cover. Thawed ice jam with hair dryer. Removed the two screws holding heating element in place and pulled element out far enough to disconnect the two wires. Reconnected wires to new element and put everything back together.
Installation instructions which came with new part were accurate and very easy to understand.
It took about 30 minutes total.
Installation instructions which came with new part were accurate and very easy to understand.
It took about 30 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaNeisha from Kerrville, TX
- Parts Used:
- WR51X10101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burned out Freezer defroster element
I had done this repair almost exactly 2 years ago. I also read in this forum about a guy who said he had to do it every 2 years... bad part design.
However, GE has replaced the original single element with a dual element, and that is what PartSelect sent me. I had to splice one wire, but the instructions were clear and it went like a breeze. Oh, and the part arrived less than 3 days after I ordered it with standard shipping. Way to go, guys! Thanks!
However, GE has replaced the original single element with a dual element, and that is what PartSelect sent me. I had to splice one wire, but the instructions were clear and it went like a breeze. Oh, and the part arrived less than 3 days after I ordered it with standard shipping. Way to go, guys! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Port St Lucie, FL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
plastic cam risers on fresh food door worn out
I unloaded the door and took the cover off at the top of the upper hinge (1 phillips screw) I then unbolted the upper hinge (2-28mm bolts) and lifted the door off. I was surprised how light it was. I laid the door down and installed the new cam riser on the door. I then unbolted the lower hinge (2-28mm bolts)and installed the new hinge.
I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.
I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from olney, IL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The plastic hinge stops broke.
I cleaned out the door and removed the top hinge. Lifted the door and layed it on the floor. Removed bottom hinge from refridgerator installed new hinge. Replaced plastic stop on door. Used broke hinge to align it and tighten. Lifted door onto new hinge and installed top hinge. Instead of buying $35 dollar hinge buy 2 plastic stops. You'll have to drill out a rivet on bottom hinge but it will save over $30.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daylyn from Houston, TX
- Parts Used:
- WR51X10101
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator not cooling // freezer running non-stop
Fortunately while my refirgerator was still under warrant I had this same problem and watched the repairman fix it. To confrm my suspicions I cleaned out the freezer compartment, removed the back panel (2 screws), and used a hair dryer to defrost it. I suggest plugging the drain hole or laying a towel in the bottom of the compartment to catch the run off or your drain pan could over low. Once defrosted I was able to verify that the element on the defrost heater was burnt. Since it was Sunday I re-assembled and cranked it back up until I could get the part. I did a goggle search on Monday, found the part instantly using only the model number from the refrigerator at PartsSelect.com. The part arrived Wednesday as promised, I repeated the process from Sunday, removed the defective part (2 screws & 2 plug in type wire connections) and she works like a charm now. I do think the manufacture of the part should consider a new design since this is the second one my unit has needed in less than 5 years. At only $27.50 ea. I should have purchased a spare to have for the next time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Yucaipa, CA
- Parts Used:
- WR51X10101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer and Fridge would stop cooling to a point of defrosting food
So our food was not staying frozen or cold so as usual i was thinking huge bill. I deceided to take a look for myself not knowing anything about a freezer. After removing all the food I noticed ice on the back part of the fridge so I just started to remove the back panel and as soon as I did that I heard the fan breath a sigh of relief. So I defrosted the block of ice and put it back together.
a few days later same thing. So on to the trusty Internet. I found partselect and helped me discover the problem of a faulty defrost heater ( who would think a heater in a fridge) Anyway I ordered the part and it was at my door in 2 DAYS!!
Thanks to PartSelect for saving me a ton of money and time. Great site! and company!
a few days later same thing. So on to the trusty Internet. I found partselect and helped me discover the problem of a faulty defrost heater ( who would think a heater in a fridge) Anyway I ordered the part and it was at my door in 2 DAYS!!
Thanks to PartSelect for saving me a ton of money and time. Great site! and company!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Medford, OR
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Emptied refrigerator door shelves. Supported door with 4x4 blocks.removed old door hinge and replaced with new.
Emptied refrigerator door shelves. Supported door with 4x4 blocks. Removed old door hinge and replaced with new door hinge and cams. Pleased with end result and dealing with PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Orient, OH
- Parts Used:
- WR51X10101
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Frig AND freezer side not cooling
This is a repair INSIDE the freezer. Turned off unit.. Unplugged. Removed shelving on freezer side. Removed freezer draw rails (4 screws total.) Removed 2 screws that hold rear panel in place at rear of freezer side (this is inside the freezer). Carefully removed metal panel by pulling from the left (side that does not have shelving clips. As noted on this website and other users, the freezer coils were incased in ice. Thawed with a hair dryer (put towels in bottom of freezer-ice was pretty heavy in mine). When thawed, remove heater element by removing 2 screws that hold it to the aluminum bracket. Then remove wires on each end. Simply install the new emelment by attaching wires back on heater and screw new unit in place. (My original heating element was a single element-you could very easily see where the heating coil inside the glass tube had shorted out. My replacement heater was a 2 element unit. This did not pose any problem at all-installs in the same manner-good directions are provided.). Replace all parts in reverse order. It's that simple. Saved probably $150. This site is wonderful! Fast shipping and the users install tips/notes are fantastic!! Will shop here again if I have to (have a Maytag washer that isn't draining and going into spin-bet the fix is on here somewhere!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Deerfield Beach, FL
- Parts Used:
- WR51X10101
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Coils at back of freezer icing over
After reading posts on this website, I determined I needed to replace the defrost heater. Removed heater to take a closer look and after testing with a voltmeter determined it needed replacing. Ordered part online and could not believe how quickly it arrived. Blue wire that travels down the left side of the freezer coils had some damage on the end of the plastic connector so was pleased to find that I was able to splice the extension wire provided in the defrost heater kit onto the blue wire and dispose of the damaged end. It's been about 10 days and I do believe my problem has been solved!
Was this instruction helpful to you?
Thank you for voting!