Models > GTS16BBSALBB > Instructions

GTS16BBSALBB General Electric Refrigerator - Instructions

Jump to:

All Instructions for the GTS16BBSALBB
121 - 135 of 339
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Loren from EL PASO, TX
Parts Used:
WR23X37285
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
merlin from TRENTON, NJ
Parts Used:
WR32X10398
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
cover was cracking on sides
removed bins ......removed cover .....replaced with new cover....replced bins back .....done !
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from EAST JORDAN, MI
Parts Used:
WR23X37285
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Light went out in refrigerator
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nicole from ST GEORGE, UT
Parts Used:
WR17X11889
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
crisper drawer shelf holder broken
Easy peasy
take the drawer out and the glass from the shelf above the drawer and the frame thet holds the glass.

Then place screwdriver at pin and knock it through. Use putty knife to pull old piece out. Then place new piece in and hammer the pin in place. Put frame back in, glass back in and drawer back in.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eleanor from OREFIELD, PA
Parts Used:
WR32X10398
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Simple
Removed old one lined up drawers, wonderful, great company to buy from and do business with, thank you
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jo from MCDONOUGH, GA
Parts Used:
WR17X11889
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Parents in assisted living. Frig was missing a shelf.
Just put the refrigerator door shelf in. Was to happy to fix this missing piece. So glad this company was able to supply an old part.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Louis from GAINESVILLE, FL
Parts Used:
WR60X31522
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Noisy fan in freezer compartment
First I unplugged the power. Then I removed the wire shelf, center plastic cover, flited the stryofoam piece out, removed the back panel. Then I disconnedted the fan connectors. Then I took the fan brackets off and removed the clamp holding the fan blades to the motor shaft. I then reversed the steps to complete the installation.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carlos from Copper Canyon, OK
Parts Used:
WR09X10107
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Start relay burned
Unplug the refrigerator removed the condenser/ compressor cover back bottom on fridge, remove the relay from the compressor took off the two wires, replace with new relay
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from CHAMBERSBURG, PA
Parts Used:
WR60X31522, WR02X12008
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Fan became noisy
First unplug freezer and empty contents, then remove the screws from the air deflector, carefully remove styrafoam air deflector block then remove back panel for easy access. Fan will be easy to switch out from there. I highly recommend the You Tube video which is where I got my basic instructions.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from Averill Park, NY
Parts Used:
WR60X46086, WR60X31522, WR02X12008
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Fan motor was not working properly, refrigerator was not staying cold enough
Ordered motor fan and grommet, swapped out the parts in about 20 minutes ,very easy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
paul from BROOKLYN, NY
Parts Used:
WR17X11889
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Broken door shelf
Slipped it it-very easy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Catherine from SEATTLE, WA
Parts Used:
40A15
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
J.Larry from TALLAHASSEE, FL
Parts Used:
WR17X11889
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
replaced a plastic shelf on the door
shelf just snapped into place. It was so simple, "even a caveman could do it."
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
THOMAS from MEBANE, NC
Parts Used:
WR60X10168
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Noisy Fan Motor
Simple. Rolled the refrigerator out , unplugged the 120 volts AC outlet.(1) Unplugged the wiring from the cabinet to the fan (white (three pin connector)). (2) Removed the two 5/16 inch screws holding the rear motor bracket . (3) Removed the fan blade from the motor shaft by applying slight pressure, pulling if off the old motor shaft. (4) removed the rubber isolator from the frame and from the rear of the old motor. (5) placed the rubber isolators back on the motor and frame. (6) Pushed the new motor back into the frame and re-installed the fan assembly. (7) remounted the fan with the rear support and the two 5/16 inch screws. Reconnected the three wire connector. Just checked the fan blade assembly to make sure they were not hitting the fan shroud. Fan blades should sit just partially inside the shroud to make sure it produces maximum airflow.
(8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ella from RODESSA, LA
Parts Used:
WR17X11890
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
None
Just place the shelf door bar in slot and push in place gentle.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTS16BBSALBB
121 - 135 of 339