TFT20JABCAA General Electric Refrigerator - Instructions

1.Emptied the stuff from inside of the fridge door.
2.Using a phillips screw driver I removed the plastic cover over the top hinge.
3. Using a small ring spanner I removed the two bolts holding the top hinge (pin), removed the hinge and lifted the door off the bottom pin.
4.Using the same spanner I removed the bottom hinge containing the broken plastic cam.
5.Replaced the broken hinge with the new one and put a little grease on the hinge pin.
6.Placed the new plastic cam on the hinge pin and refitted the door.
7.Replaced the top hinge and plastic hinge cap, Job Done!

A couple of points a) When your plastic cam needs replacing, always buy the hinge pin & plastic cam. The pin has a plastic cam welded to it and as this is the partner of the plastic cam it will also be worn so you should replace them as a pair.
b) You will spend more time cleaning the 'out of the way' parts of the fridge than actually carrying out the repair.

My fridge is now as good as new.

Removed the upper hinge assembly. Removed the door. Removed the kick plate. Removed the old hinge assembly and installed the new one.Replaced the other broken cam on the door bottom. Then,reinstalled door to fridge and reinstalled the top hinge. PS/cleaned and lubed both upper and lower hinges.

First removed plastic cover off top hinge with phillips screwdriver. Used nut driver to loosened screws on upper hinge to 1/2 inch out and then used wood blocks to shim up door as high as possible while still in closed position. Used socket wrench to remove lower hinge and fitting from bottom of door, while still closed. Installed new lower hinge and door fitting with socket wrench. Lowererd door to sit on bottom hinge and then adjusted position of top hinge before tightened those screws with nut driver. Reinstalled plastic cover. Piece of cake!

Removed all items from the door shelfs.
With the door open, picked up the door and slid it upward as far as it would go. Asked wife to place a stack of books under the door to keep it at the proper height. Removed the lower hinge pin assy. remved the door stop. Installed new componets and reinstalled the door stop. The door was now level with the freezer door.

I had to remove the top hinge of the door and shut off the water supply to the automatic ice maker. I then unhooked the water line and pulled it through the guide as I took the door off. Once the door was off, I removed one bolt with the nut driver and replaced the cam. I reversed the above actions and replaced the door. It is very important to adjust the door so the seal fits tightly and evenly all round the door. It was a relatively simple procedure that went very smoothly.

Lifted the door while closed into position even with freezer door. Then put srap pieces of wood under door to hold into place while I removed the old hinge assembly and replaced with the new one. The door works good now. Make sure you replace both peices as they will both be worn.

Followed other messages to complete fix. Simple overall.

Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.

I could see a broken part but couldn't tell exactly how it was oriented on the hinge. I bought just the cam riser but then thought I needed the hinge kit based on what I read on this site. Then I saw better pictures of the hinge kit on another site & realized there are 2 cam risers that meet. The one riveted to the hinge was fine (in my case) - I only needed the upper one...a very inexpensive repair. Do NOT remove the door for this repair. Slide the door up a bit while closed and use a pint-sized paint can to prop it up. Make the repair and remove the can...done.

First I bought the right tool to remove the hinges.
Then replaced the hinge with the two cams.
Now the door closes itself.

Just remove all items in door shelves, remove screw holding top hinge cover on. Remove two bolts holding top hinge and remove hinge from door. Carefully open door and lift out of bottom hinge. Remove screw holding bottom hinge on door and replace broking cam riser. Reinstall door in reverse order and adjust top hinge where both doors are even across the top. Thats it!!!!!

Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.

they sell the cam piece but the instructions says not to replace only one part. so beware you need both the cam and hinge as a kit .

Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.

Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.

Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.