CSB48WP2RBS1 General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randell from Rancho Cucamonga, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed replacing
Very easy, unscrew and re-screw new filter in..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from cocoa, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer would not defrost
There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randel from Centreville, VA
- Parts Used:
- WR17X22070
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Little or no flow to water dispenser.
Adding a small amount of water to the filter would resolve the problem for a week or two. So, I thought this was an issue with the filter and decided to try the bypass cap to help zero in on the problem. The bypass cap had no instructions concerning the need for O ring so it was trial and error. The O ring was not needed. After installation of the bypass cap, no water flow resulted and I had to replace the filter. Intermittent problem continues.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from La Grande, OR
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter was aged and needed a replacement
unscrew filter and replace the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Surprise, AZ
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
We needed a new water filter.
We received the part just a few days after ordering, unscrewed the old filter by hand, and installed the new filter the same way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Temple, TX
- Parts Used:
- WR17X22070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Installed whole house filter, did not need refrigerator filter
Removed water filter and inserted plug (works great and water flow increased)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Saint Charles, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrige ws too cold
as per video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalia from Mount Pleasant, SC
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replacement
Removed the old filter. Filled the new one with water and put it in theplace of an old one. Flushed the system with 1 gallon of water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela J. from Sun City West, AZ
- Parts Used:
- WR17X22070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Removed water filter as I have a whole house filter system.
Just removed the filter and used my hand to attach the water filter bypass cap....did not even need to turn off the water first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from San Antonio, TX
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Poor water and ice taste, filter a few years old.
Very simple, I followed instructions sent with the filter. Twisted old filter clockwise 1/4 turn to remove. Filled new filter with water, lined up arrow on filter to arrow on refrigerator, and then turned 1/4 turn counterclockwise. Filter raised and seated itself. Wiped few drops of water from refrigerator shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Craig from Diamondhead, MS
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed replacing
Folowed instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from selbyville, DE
- Parts Used:
- WR17X22070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water dispensed slow and filters too expensive and not very reliable
I just unscrewed filter and screwed in filter bypass
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donnie from metairie, LA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced filter
none required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Rancho Cordova, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator freezing.
Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.
Was this instruction helpful to you?
Thank you for voting!