MTG16GBMCRWW General Electric Refrigerator - Instructions

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

Ordered part came in 3 days. Removed plug and rear cover. Pulled off old fan . Installed new fan by pushing it on to shaft. Plugged unit back in to check operation, installed rear cover. Done. Part fit perfect. Thanks to this site you folks are great !

Unplugged the refrigerator then used the cordless drill to remove the 6 screws on the access panel on the back of the fridge to be able to get to the fan. Was able to pull the fan off by hand and push the new fan on by hand. Plugged the refrigerator by in and watched the fan run for a few minutes then replaced the access panel. Really quick and easy repair.

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

took a little more effort than the video show to remove old module and replace new. Works fine now.

It was way to ez to install only a couple of minutes that's it

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along.
That helped us finish the installation.
Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.

i found that the door was to low was the problem shimmed the hinge on the bottom brought the door up so the gasket was ok so isent the new gasket back to you never attempted to change so i dont have any thing to tell you about instalation difficulty carl phillips