PCE23NHTDFBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bobbie from Highlands Ranch, CO
- Parts Used:
- WR17X11505
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Disp
Replaced crusher disp, but had to order the back plate(didn't realize it was two piece) waiting for that part. It was very easy to do. Had to use two drivers to pop out of ice bucket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from LA QUINTA, CA
- Parts Used:
- WR17X22070
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replace water filter with bypass plug - filter is redundant with home osmosis system
If you have a reverse osmosis system for filtered water system in your home that also feeds the refrigerator, using another water filter in the refrigerator is redundant, so GE makes a Water filter Bypass Cap that allows you to run using the already filtered water without needing to expensive water filter. FIRST - using a phillips screw driver remove the toe kick plate at the bottom front of the refrigerator - two screws - one on each side of the plate that extends the entire width of the refrigerator. SECOND - Locate the water line (should be right in front) and the valve to turn off the water. Turn valve clockwise (right) until completely closed. Then test by attempting to fill a glass with water using the dispenser on the door. If any water continues to come out, continue turning the valve (without forcing it) clockwise until it has been turned as much as possible. If water still comes from dispenser, locate the source of the water line - most likely from under the kitchen sink. There should be another valve under the sink, or simply turn off (turn the cold water valve clockwise) until water cold water completely turned off. Test again as required. THIRD - clear the top right hand back shelf directly under the water filter screwed into the ceiling of the refrigerator in the rear top right side of the refrigerator. Place a small towel under the water filter, and slowly turn the filter 1/4 turn clockwise without using force. Continue turning until the full 1/4 turn is complete and the filter will drop down without pulling. Place the old filter upside down in the sink, thereby allowing the filter to drain any water present in the filter. FOURTH - remove the filter plug from package, notice notches in top of plug that align with gaps in the area where a filter would typically be screwed into the filter location in the ceiling above the top right shelf in the refrigerator. After aligning notches in the bypass plug with gaps in the screw mechanism, carefully turn the bypass plug 1/4 turn counter- clockwise - at which time the bypass plug should be firmly installed. FIFTH - Reverse step SECOND, and turn valve Counter-Clockwise until valve is completely open. Test to ensure no water is leaking from the Bypass Plug. SIXTH - Finally reverse step FIRST by reattaching the toe kick plate using the two phillips screws removed in Step FIRST. NOTE: The Bypass Plug is quite inexpensive, but after adding shipping from Canada - the cost is about the same as purchasing a new filter for the refrigerator. :-(
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from STATEN ISLAND, NY
- Parts Used:
- WR01X10315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice bucket Auger would not make ice to come out
Remove bucket
on a work bench remome to bottom screws, one top screw from ice shield. Remove front cover, then lift out part that hold the auger in place.
then remove Auger nut JUST REMEMBER THE AUGER NUT IS REVERSE THREADS. replace new auger nut and reverse the above procedure. VERY EASY
on a work bench remome to bottom screws, one top screw from ice shield. Remove front cover, then lift out part that hold the auger in place.
then remove Auger nut JUST REMEMBER THE AUGER NUT IS REVERSE THREADS. replace new auger nut and reverse the above procedure. VERY EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from VANCOUVER, WA
- Parts Used:
- WR01X37886
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water dispenser bulb burned out and needed to be replaced
Unscrewed old bulb, inserted and screwed new bulb into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monica from RENO, NV
- Parts Used:
- WR71X10764
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
plastic on front of shelf had been broken for FOUR years
repair (replacement of the broken piece) took less than 2 minutes. I can't believe I waited so long to fix this. Piece was expensive, especially after shipping costs -- but now it looks brand new so I am happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E from PHOENIX, AZ
- Parts Used:
- WR32X26198
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The back corners broke off.
The snack pan is pulled out then lifted slightly and pulled out fully. The new snack pan is then aligned in the slots and pushed in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DRAGOON, AZ
- Parts Used:
- WR32X26198
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front of drawer was broken
Remove one and put in the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MOUNT VERNON, IL
- Parts Used:
- WR71X10973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The bottom was cracked
Just replaced it with new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from MIAMI, FL
- Parts Used:
- WR01X37886
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light bulb at water dispenser not working.
unscrewed old bulb and screwed in new bulb. checked and new bulb works great. less than five minutes to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHNNY from FORT WORTH, TX
- Parts Used:
- WR02X10585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
frost build up
flapper then bought the spring
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nina from SANTA MARIA, CA
- Parts Used:
- WR74X10270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Broken Kickplate
Easy to install. Looking at the side of the existing kickplate that was not broken helped to know how it should look when installed. New part worked great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from Cameron, NC
- Parts Used:
- WR02X45209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
leaking water around lip of tube.
Repair went well. All i needed was the more expensive part. The other I did not need.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- susan from hartford, WI
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Bad tasting ice cubes
Took the old filter out and put the new one in.
Easy Breezy!!
Easy Breezy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from MORENO VALLEY, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water dispensed at a trickle
I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from columbus, OH
- Parts Used:
- WR01X37886, MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water Filter and Light Dispenser replacement
My water filter was a breeze to install. Just push up and to the right and it locks right in.
As for the Water Dispenser light. Just screw it in!!
As for the Water Dispenser light. Just screw it in!!
Was this instruction helpful to you?
Thank you for voting!