DPU21BRDABB General Electric Refrigerator - Instructions

Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!

Cake walk repair.

Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, tighten and install cover. tool me 6 minutes.

First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif

removed door, removed old cracked riser aand replaced with new. You have a easy to follow parts site and very good prices. I will use you for all my future repairs.

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done

I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!

After recieving the part overnight (Very unexpected speedy delivery!) I propped the freezer side door up with a 4x4 and 2x4 and the old part came right off and the new part went right on with no hassels, Done in less than 15 min!!!!
The new part even came with step by step easy to follow directions.

Removed 2 screws holding top hinge. Removed door. Removed 2 screws that holds the door stop and cam riser replaced cam riser, provided, replaced stop and screws. Removed 2 screws holding lower hinge replaced with hinge, provided, replaced screws. Put door in place and replaced top hinge and srews. Job done

unclipped and replace with new part.

Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.

Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.

Look at various pertenant DYI articles and videos on the internet. Replaced water filter with bypass plug. Checked water flow to icemaker water solenoid. Ran icemaker diagnostic test which failed. Ordered replacement. On receipt of replacement, began replacement work. To wit: Pulled fiidge from wall and unplugged. (Not necessary to shut water off.) Removed small freezer basket. Unloaded main freezer basket, removed it then removed the freezer door. (A screw on each side bolts the door rail of the chassis slide to the freezer chassis slide.) Loosened screws on rear, top of partition between icemaker and small freezer basket. Pushed up on partition front and popped out U-bar supporting partition bottom being carefull not to bend it. Removed same. Removed screws from partition and set aside. Removed grilled "thingy" between rear of icemaker and partition. Now have access to icemaker screws. Loosened the screws, pushed up and out and carefully let it hang by it's connector. Fiddled with the connector locking tabs and finally got it loose. Compared old and new icemaker. Have to keep the old water funnel. The new wiring harness was stiff and the connector had a different orientation. Twisted both the wiring harness and connector to align connector while the icemaker hung by it's cable being careful not to let the icemaer slip and fall to the bottom. After much fiddling, got the connector inserted and locked. Set icemaker over the two screws, pulled it down and tightend the screws. Put the old funnel into the new unit being very careful to get it right the first time. Put grilled "thingy and the partition and U-bar back in, put door back on, put the ice cube bin back, freezer drawers bac and reloaded the frozen food, plugged fridge in. Done! Time to replace icemaker was about 20 minutes and another 2 hours to do the rest ofthe work. Still required only a nutdriver and phillips.

unplug refrigerator. Remove Ice bin then remove the cover off the ice maker,(slides off from bottom then lift off top) no reason to remove ice maker completely. Remove center gear screw and remove main gear from Ejector blade. remove (3) screws holding the front plate. The motor and switches are attached to this plate from behind, do not remove the nut from the from the stud that adjusts the travel for the motor. The Motor and switches will come upt with the plate and the shut off arm will come out of a hole in the top right. Its ok just be careful when you put it back to get it in the hole. remove the old cam and replace it wint the new one and reassemble. Its a bit tricky to get all of the microswitches over the new cam just carefully wiggle the plate and cam and don't push too hard. once everything is lined up it should go back together and you can replace the screws and main gear :)

The video to replace the flapper looks easy, howerer the first step is to remove thestic cover of the icemaker. In my refrigerator model (as oposed to teh one shown n teh video) teh coved if firmly attached and goes under the refrigerator external plate so I was never abel to take it oot (so step 1 failed).
I was able to replace the flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!

son did the work BUT ONLY AFTER- trying to order the part from Sears parts online, in which they never from the right part and i spent 1 and 1/2 hours on chat and finally gave up. THEN i called sears replair, made appointment for two weeks later requesting 1st repair time of the day, was asured the repair would take place between 8-12 and beacuse it was 2 weeks away it should be the 1st repair. The day of the appt I received a phone call at 11:38 saying they would be here about 12:20, I SAID NO THANK YOU< OUR AGREEMENT WAS BY 12:00. THen I got online typrd in water tank your company come up, showed photo, and price which i ordered it can in my son fixed it and all was complete within an hr.