ZISS360DNDSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- christi from round rock, TX
- Parts Used:
- WR60X10185
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Refrigerator making lots of noise in freezer
Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.
The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.
The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Placida, FL
- Parts Used:
- WR60X10185
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Annoying Whistling Noise
Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Foresthill, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water Filter Red Light
Replaced Water Filter (twist off old filter; twist on new.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Fort Worth, TX
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice and Water Filter needed replacement
I watched the video, and noticed that they did not even turn off the water. The replacement took less than 30 seconds once the filter was filled with water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Green Valley, AZ
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new water and ice filter
simply read the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Enterprise, AL
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water tasted funny
Simply twisted off the old water filter, unwrapped the new one and twisted it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Elk Grove, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter change
easy easy easy!!!!!
Was this instruction helpful to you?
Thank you for voting!
Replace Dispencer blade
Removed the exterior 4 screws and 1 holding the metal rod underneath. Sepearated the plastic parts pulled out the dispensing mechanisim. Removed the lock washer, then removed the spacers and blades. Put the new blades in with the spacers and reversed the other steps and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from asheboro, NC
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace the filter
replaced the filter with the new one i purchased
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Waynesboro, PA
- Parts Used:
- MWFP
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
replace water filter
Easy, with included video and instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREGORY from SACRAMENTO, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change Filter
My 14 year old Son
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irene from Tigard, OR
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice and Water Filter needed replacement
It was easy and fast, like changing a light bulb. The directions were clear and easy to follow. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendell from Baton Rouge, LA
- Parts Used:
- WR60X24484, WR02X12149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rat chewed up fan blades in refrigerator at our camp.
We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from fort worth, TX
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
did not need adapter
exactly as the instructions.......never did see anything about replacing the adapter...therefore i did not
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!