PYE22PYNGFS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from SPRINGFIELD, SC
- Parts Used:
- WR07X10131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Compressor would run for three seconds and stop, two minutes and repeat.
The overload protector was the problem. It plugs into the side of the compressor and the run capacitor plugs into it.
If you pull the overload protector and it rattles when you shake it, that's probably your diagnosis.
The replacement is different from the original and the wire connectors are different. Hold the thing in the same orientation as if it were plugged in. The vertical connector goes to the neutral wire, which on my fridge is orange. The horizontal connector is for the overload, which for mine is black and white. If you have a schematic you should verify the wires yourself.
Anyway, the refrigerator now works like new.
If you pull the overload protector and it rattles when you shake it, that's probably your diagnosis.
The replacement is different from the original and the wire connectors are different. Hold the thing in the same orientation as if it were plugged in. The vertical connector goes to the neutral wire, which on my fridge is orange. The horizontal connector is for the overload, which for mine is black and white. If you have a schematic you should verify the wires yourself.
Anyway, the refrigerator now works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from NORTH PORT, FL
- Parts Used:
- WR32X10912, WR02X13658
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The roller bearings on the Salad/ vegetable storage bins broke and the bins would not slide easily.
Replaced both Crisper Drawers with new units which had the roller bearings attached. Very poor factory design of the roller bearings attachment which have not been improved in the replacement drawers. I expect this problem to repeat a few years down the road.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elias from PARKER, CO
- Parts Used:
- WR55X30604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lights in the refrigerator were very dim
I determined one of the five LED lights in the refrigerator was dead by swapping it with a working one. The refrigerator lights are wired in series and if one of the lights is dead the remaining ones turn on, but very dim. I called PartSelect.com and thanks to their help we determined the correct part to order which is the oval-shaped cover LED assembly which includes the cover, LED, and female connector. The part from PartSelect arrived in three days. The oval-shape LED plastic Cover assembly is mounted on the refrigerator and held by a couple of side latches. First unplug the refrigerator and then proceed to lightly pry the oval-shaped cover side facing the rear of the refrigerator with your finger nail to remove it. With the LED cover removed you can then press on the LED connector tab to slide it off. Now slide the female connector of the replacement part to the refrigerator male connector and snap the oval-shape plastic cover onto the refrigerator receptacle and then plug it back to its outlet. Now all the lights in the refrigerator should light up brightly! That's all folks. Hope this helps. Good luck. Yours truly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SUN LAKES, AZ
- Parts Used:
- WR71X11046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door shelf
It snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from OAK FOREST, IL
- Parts Used:
- WR71X11044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf on right Door Broke - Fell apart
Once I received that New Part, just place the 1 Piece from the old Shelf into the New Part and mounted the Shelf in the Door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from FAIRVIEW, MI
- Parts Used:
- WR17X13060
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
switch went bad
just removed the old switch and replaced it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from NORMAN, OK
- Parts Used:
- WR02X23032, WR11X10031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
COVER LATCH BROKEN
I recieved the package with the correct part number but the wrong part inside. The item in the package does not even resemble the part on the GE parts website. Tried to contact parts select but no luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- elissa from ASHBY, MA
- Parts Used:
- RPWFE
- Difficulty Level:
- Very Easy
- Total Repair Time:
- More than 2 hours
Replaced thermistor 5.2 ohms of resistance
Exposed evap defrosted with heat gun exposed defrost element defrost termination switch ok therminster didn’t check out the thermistor sends the signal to logic panel then run the the freezer ice machine and refer temps it took 24 hours before the system starting to show results freezer compartment 10 below ice compartment 0 degrees refer temp 37 degrees one refrigerant three different temps system is running at optimum performance 450.00 $ service call the thing with GE appliances there is no wiring diagram .thankyou parts select .ill use you on all domestic service calls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from ANKENY, IA
- Parts Used:
- WR32X10910
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The middle support for the vegetable door roller wheels broke
Removed drawers, lifted out old frame assembly ( no tools ) removed and cleaned old glass from assembly.
Carefully screwed old rollers ( x4 )into new frame, then placed old glass in new frame, repositioned frame into refrigerator and then repositioned drawers in frame.
20 minutes , no issues
Carefully screwed old rollers ( x4 )into new frame, then placed old glass in new frame, repositioned frame into refrigerator and then repositioned drawers in frame.
20 minutes , no issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy G from Matthews, NC
- Parts Used:
- WR49X10322
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The ice maker worked great and the crushed ice dispenser worked fine but the cubed ice dispenser sounded like it had a stripped gear.
Once I opened the left hand door and removed the ice bucket, I simply removed the 3 small screws and removed the old part and replaced it with the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from LAKE PLACID, NY
- Parts Used:
- WR71X11063
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace butter compartment on GE Profile
It just snapped in. Fit perfectly. Excellent service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Petoskey, MI
- Parts Used:
- WR12X31641
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
New SS refrigerator had scratch across both handles while staged awaiting installation of new flooring.
Simply loosened Allen screws and removed handles then affixed new handles and tightened Allen screws in the new handles. Discarded scratched handles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Salisbury, NC
- Parts Used:
- WR71X11045
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I dropped The top left bin and it cracked
Popped it up and popped new one on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- QUOC-LOC from LYNN HAVEN, FL
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The control board generated clicking noise. Temperature display wrong values.
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from White Plains, NY
- Parts Used:
- RPWFE
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Water filter needed changing.
Snap filter into place while holding the filter slightly away from the refrig. When filter snaps into place, push it towards refrig into place.
Was this instruction helpful to you?
Thank you for voting!