Models > GCE23YETBFWW

GCE23YETBFWW General Electric Refrigerator

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
The main control board relies on this thermistor, or temperature sensor, for readings from inside the refrigerator or freezer. Those readings guide cooling decisions, including when the compressor and...
In Stock
Order now and your part arrives by Nov 28
Measuring approximately 1 inch in diameter and helps reduce vibration transferred from the running motor, this red evaporator fan grommet cushions the fan motor at its contact with the mounting bracke...
In Stock
Order now and your part arrives by Nov 28
This genuine OEM light switch is used to control the light in your refrigerator. When the fridge door is closed, it depresses the switch and turns the light off. When the fridge door opens, it release...
In Stock
Order now and your part arrives by Nov 28
This OEM compression ring is used to hold the evaporator fan motor in place. Signs that you may need to replace the compression ring are if the fan is noisy, or your fridge or freezer are too warm. We...
In Stock
Order now and your part arrives by Nov 28
$15.26
This genuine OEM replacement part is a bumper for your refrigerator. The bumper is made of orange rubber and measures less than half an inch in diameter. The bumper is used to prevent the fan motor fr...
In Stock
Order now and your part arrives by Nov 28
Control the opening and closing of the ice chute door with this plastic dispenser crank. It sits behind the dispenser interface on the inside of the freezer door and moves when activated by the dispen...
In Stock
Order now and your part arrives by Nov 28
For freezer airflow, the three-blade evaporator fan blade circulates air through the refrigerator and helps remove heat. It is an OEM replacement part. Confirm fit using your appliance model number.
In Stock
Order now and your part arrives by Nov 28
This part is the replacement water line for your refrigerator. It is a long plastic tube, which is 5/16 of an inch in diameter. If your refrigerator is leaking, or will not dispense water or ice, you ...
In Stock
Order now and your part arrives by Nov 28
In Stock
Order now and your part arrives by Nov 28
This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unu...
In Stock
Order now and your part arrives by Nov 28
A press of the dispenser paddle activates this refrigerator dispenser micro switch, sending the signal to release water or ice. Taking your cup away releases the switch to stop dispensing. Installing ...
In Stock
Order now and your part arrives by Nov 28
In Stock
Order now and your part arrives by Nov 28

Common Problems and Symptoms for GCE23YETBFWW

Viewing 21 of 21
Fridge too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Fridge too cold
Fixed by these parts
Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Light not working
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Freezer not defrosting
Fixed by these parts
Fixing Fixing
How to fix it
Not dispensing water
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Fridge and Freezer are too warm
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Frost buildup
Fixed by these parts
Fixing Fixing
How to fix it
Too warm
Fixed by these parts
Fixing Fixing
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Fridge runs too long
Fixed by these parts
Fixing Fixing
How to fix it
Ice maker not making ice
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Freezer too cold
Fixed by these parts
Fixing
How to fix it
Door Sweating
Fixed by these parts
Fixing
How to fix it
Door won’t open or close
Fixed by these parts
Fixing
How to fix it
Clicking sound
Fixed by these parts
Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing
How to fix it
Doesn’t stop running
Fixed by these parts
Fixing
How to fix it
Too cold
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Gerald from San Clemente, CA
Parts Used:
WR55X10025, WR02X10552
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Fridge too warm, evaporator icing up
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.
606 of 738 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
michele from North Smithfield, RI
Parts Used:
WR55X10025
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
my refigerator was warm but the freezer was cold and working correcttly
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.

I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more />After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.

I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
305 of 405 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Marc from Orlando, FL
Parts Used:
WR49X10091
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Refrigerator too cold
My repair experience was a little more complicated than previous posts, but nothing major. And most importantly replacing the Fresh Food Air Inlet Cover did fix my problem. Here are the steps I followed:
1. You will need to remove a minimum of the top two shelves to get access to the Air Inlet Cover. It runs along the back of the fridge and connects to a hole to the freezer side. It has a little fan inside that sucks the cold air from the freezer and diverts to the top and bottom of the fridge.
2. As mentioned in other posts, there are four screws holding the Inlet Cover in place, 2 lower and 2 upper. To get access to the lower two screws,you simply pop off the lower duct assembly (squeeze the sides). Be careful when removing and installing these screws. If you drop one into the lower duct, you will add a few more steps to the installation to remove more shelves and take out the lower duct to get to where the screw fell. Obviously this happened to me. Not difficult to do, just adds more time.
3. To access the upper two screws I had to remove the top light cover (one screw) and then slide out the top duct/diffuser assy (my name, not GE's).
4. Finally to get clearance to pull out the Inlet Cover, I had to remove the water filter and cover. When you pull away the Inlet Cover, you will see the electrical connection that is simple to disconnect.
5. After I removed my Inlet Cover, it was obvious that it was broken because it rattled and I could peek inside to see that the plastic air diverter/flapper thingy was broken.
6. One final surprise was that the replacement Air Inlet Cover did not exactly match the one I removed. The replacement only had one upper air outlet, while my old one had three upper outlets, left, right and center. I noticed there was a plastic cover over one of the side outlets on the replacement, so I just popped that off and hoped for the best.
7. The replacement Air Inlet Cover Kit came with sticky back insulation that you attach to where the Inlet Cover meet the freezer access hole to make sure snug fit to limit extra cold air leaking into the fridge side.
8. Installation of the replacement Air Inlet Cover was fairly easy, just follow the above steps in reverse and make sure you don't drop any screws.
It's been a couple of weeks since I performed this installation and my fridge has been maintaining temperature perfectly. No more frozen milk or lettuce. The wife is very happy.
156 of 163 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!