CWE23SSHSS General Electric Refrigerator - Instructions

Remove the screws from the two door pivot covers. Remove the covers and set aside. Remove the screws from the control board; disconnect the electrical connections; remove the door light switch, install door light switch then reinstall everything.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

Safety first, unplug fridge. Had to remove the top access panel, which consisted of 5 screws. Got access to the door switches. These are removed from the panel by depressing the plunger on the switch and sliding them out of the retainer. Transferred the wires over to the new switches one for one. Re-assembled. Dispenser works.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

Pulled out bottom crisper drawers. Removed drawer slides. Removed side plastic panels, then removed back panel which exposed the fan. Removed fan and replaced with new fan. Had to use the heat gun because there was ice buildup on left corner of rear panel. Reassembled in reverse order. There is several excellent videos on You Tube.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

I followed the directions included with the water filter and it was simple. The only problem I had was not being strong enough to easily remove the old filter. I did accomplish that after a few tries and the rest is history.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Replace fan . Fairly easy.

Pulled the instructions up on U-tube and followed them. With the socket removed 5 small bolts. Took the old switches ( I replaced both switches being I had it apart), put the new switches in and then put the 5 bolts back in.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

I diagnosed the sensors in my refrigerator by holding the sensor in and seeing if I could trick the sensor it partially worked. I then used a multimeter and did an ohm test on both sensors multiple times open and closed the switch to verify which switch failed because it worked a couple times but not always. It ended up being the switch on the left hand door with 3 terminals on it and after the replacement it has worked great for weeks now no issue. best 15 dollars and 25 minutes spent!

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.