GTS18FBSW General Electric Refrigerator - Instructions

1) TURNED POWER OFF FROM REFRIGERATOR 2) REMOVED THE FREEZER SHELF FIRST BY GENTLY TAPPING THE LEFT SIDE UP AND OUT THEN THE RIGHT SIDE UP AND OUT 3) REMOVED THE 2 PHILLIPS SCREWS HOLDING THE EVAPORATIVE FAN COVER IN PLACE 4) GENTLY PUSHED THE COVER UP AND MAKING SURE THE 2 CLIPS WERE NOT DAMAGED 5) VERY GENTLY PUSHED UP ON THE STYRO FOAM SHIELD GRASPING IT FROM THE BOTTOM, BE VERY CAREFUL NOT TO CRACK OR DAMAGE THIS 6) THEN REMOVED 4 OF THE PHILLIPS SCREWS HOLDING THE BACK PANEL 7) THEN REMOVED THE 2 SCREWS HOLDING THE FAN MOTOR IN POSITION ON THE BACK COVER AND LAID THAT ASIDE 8) I COULD THEN SEE THE MOTOR SO I UNCLIPPED THE RED/DARK WIRE CLIP FROM THE HARNESS WITH MY FINGERS, THEN TOOK MY NEEDLE NOSE PLIERS AND GENTLY PULLED UP ON THE GREEN GROUND WIRE 9) I THEN REMOVED THE 2 PHILLIPS HEAD SCREWS HOLDING THE MOTOR BRACKET TO THE WALL OF THE FREEZER 10) THEN REMOVED THE ENTIRE MOTOR AND PUT THAT ON THE KITCHEN TABLE 11) TOOK MY NEEDLE NOSE PLIERS AND VERY, VERY GENTLY PRIED OFF THAT LITTLE METAL RING HOLDING THE FAN BLADE ON (TRICKY SO LEFT UP GENTLY)...I BOUGHT ADDITIONAL IN CASE I DAMAGED IT 12) TOOK MY 5/16 NUT DRIVER AND UNSCREWED THE TOP METAL BRACKET HOLDING THE MOTOR 13) LIFTED THE MOTOR OFF AND LOOKED AT THE TOP AND BOTTOM GROMMETS TO SEE IF DAMAGED OR CRACKED (I BOUGHT ADDITIONAL GROMMETS IN CASE THEY WERE CRACKED OR DAMAGED, EASY FIX) 14) THEN ATTACHED THE NEW MOTOR AND BASICALLY SIMPLY DID EVERYTHING IN REVERSE TO INSTALL THE NEW MOTOR. MAKE SURE YOU KEEP YOUR SCREWS IN ORDER SO YOU CAN IDENTIFY WHICH PART THEY CAME FROM. MAKE SURE YOU DO NOT PINCH AND WIRES WHEN RE-INSTALLING THE MOTOR. SAVED ME A REPAIR PERSON CALL.

Took out old put new in. Watched a u tube, no problems

Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new gasket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.

I did not do the repair but observed a friend trying to replace gasket in refrigerator. It was a very difficult procedure. He works as a handyman so he knew what he was doing and had to manually fit gasket with some help with a hammer. Gasket did not go in easy and had to be forced to fit until job completed/

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

Took the bracket out of box and install it like the video showed me..very easy to install..

Just popped them in their slots. Very easy and it made my refrigerator brand new again.. Thank you

Click shelf into place!

I order the small part and installed it myself, it was very easy with "part select". I will refer them and use them in the future. Thanks parts select.

First, remove the cardboard cover on the back, lower portion of the refrigerator.

Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)

Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the blade shaft toward the motor (away from the fan blades) to loosen.

Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.

Reverse the above steps to attach the new blade.

Easy

I first washed old shelf to make sure glass will easily slip out. Installed old glass and replaced.

Went right on

replaced lights in refrigirator and freezer

I ordered the new part from PartSelect and it was delivered very quickly. I removed the part from the box, laid the old glass shelf inside if it and placed it in the fridge. No tools required, and then slid the vegetable drawers into it and replaced the food. Very satisfied with my purchase experience.