RG2300NGPCR0 General Electric Refrigerator - Instructions

First remove trim surrounding ice/water dispenser assembly. Use a flat spackle knife to obtain space between door and trim. Be careful not t scratch refrigerator door. Then pry trim off. This was the most difficult part of repair. The front plate of the dispenser is held to the back of the dispenser by two friction fastners and in the case of my refrigerator a phillips screw (some don't have screw in middle). Use a small round tool like an allen wrench to push up on the 2 fastners to release them. Next push the front assembley aside and remove the 4 screws holding the back part of the dispenser. Push that assembly aside. Remove the defective solenoid assembly by removing the 3 mounting screws. The solenoid base can be worked out by slipping it out of the solenoid assembly plunger still attached to the dispenser door assembly. Next slide the plunger off of the dispenser door assembly. Install new solenoid assembly by reversing this procedure.
Hint - I found the ice door assembly (wr17x11653) also needed replacement and it is well worth the effort to replace both at the same time.

The model we have, the front panel snaps into place. It was removed for access and the electrical connectors unplugged. Four screws and the chute assembly was removed. Removing three screws and opening the chute door allowed the solenoid assembly to be removed without removing the door assembly. All parts and area were cleaned and the assemmbly was the process in reverse.
Guideline to prolong recurrance: always put ice into glass first to reduce splashing of ice falling into liquids causing the solenoid armature to rust and stick.

Squeezed a flat blade screwdriver between the faceplate (buttons and lights) and the plastic part behind it and the front panel popped loose. I unscrewed the 4 cross-slotted screws on the panel behind the faceplate and could easily see the solenoid. I released the solenoid connector from the printed circuit board and removed its 3 screws. It slides out. Replace with new part in reverse.

I was doing a replacement so it was just a matter of removing old parts and replacingn them with new ones.

Removed controls face plate by inserting small screw driver into small holes located below the face plate releasing internal fastening catches and permits you to pull the face plate down and out toward you. Remove the electronic panel now exposed covering the solenoid by removing the 4 screws in the corners. Detach the electrical connector leading from the solenoid ( It may be prudent to unplug the refrigerator as a safety proceedure). Proceed to remove 2 screws holding the solinoid. If the sollinoid is corroded and difficult to remove and disengage from flap(door) controling the ice shaft aperture, it may be necessary to remove the flap by removing 2 small screws holding it in place. Be careful to note the small spring on the left hand side of the shaft which the flap rotates around since it to be re installed in the proper position when the parts are reassembled since it closes the flap after it is opened by the solonoid.
Reconnect the parts and and snap face plate back into place. Good Luck

Remove dispenser assembly in freezer door & replace solenoid.

Removing the trim ring around the control panel is the hard part. Be sure to watch the video on how this is done.
Follow the video instructions on how to remove the solenoid and you will not have any trouble.

Replace solenoid which controls the despenser door. It is usually rusted. The front panel snaps off easily. Then there are 4 screws for the panel. Once the panel is off, the solenoid is exposed. There are 3 screws for the solenoid. You may want to spray dw40 on the screws if they are also rusted. Make sure you turn fridge off before performing this repair.

I watched the video explaining how to do this and it was a snap. MY PROBLEM WAS COMPLETELY SOLVED. Partselect.com is a must for my household. I couldn't be happier!!!!!

First I used an ice pick to punch the tabs under the control panel to remove the ice/water selector panel. Then I used a phillips screwdriver to remove the solenoid switch. Unplugged the switch and re-installed with new one I received in 2 days and shazaam it works like new.

First I unplug solenoid from board. I then removed 3 screws holding it in place. I removed bad solenoid (it was very apparent once I took it out). I placed the new solenoid in place, replaced the 3 screws and plug the cord into the circuit board. Success!

Using a small phillips I removed the plastic module containing the ice/water selection buttons by sequentially inserting the screwdriver into 3 holes just underneath the module in the chute opening and pushing up on the tabs while pulling out on the module. Pulling the module away exposes 4 screws that are easily removed allowing you to remove the chute assembly. The solenoid is removed by removing 3 screws and pulling the clip containing the solenoid wires off the electronics board. Reverse the process to replace.

I followed the easy video online that was mentioned in the paperwork that came with the part. The day before I replaced the flapper door for the ice chute and when I saw the rusted solenoid I immediately ordered that part which arrived the next day. I did not need to remove the border around the water/ice dispenser access area as shown in the video to install the parts. I did use a tiny screwdriver to press the little tabs on either side at the bottom of the front panel to release it to get to the parts. I was able to remove and replace the solenoid within minutes. And this was my first ever appliance repair attempt!

Used ice pick on bottom of water/ice cover plate to pop it loose. Removed 4 phillips head screws to gain access to the solenoid. Removed and replaced solenoid. Reinstalled parts removed to gain access to the solenoid.

I followed the instructions that were posted on the partselect website and the video tutorial. It really was as simple as everyone had commented. Like others have noted, once the small tabs on the bottom of the faceplate were released, the cover came right off. Unplug the wire connectors, don't force them off. Remove the four screws and voila, there's the whole system laid out in front of you. It took me longer to clean up all of the gunk that had built up over the years. Once the new part was installed, everything went back together veray easily. The machine works like new again. Thanks partselect, you saved me some serious $$$.