TFG22JADAWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Warren from Bath, MI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dorr would close properly
Lifted the door while closed into position even with freezer door. Then put srap pieces of wood under door to hold into place while I removed the old hinge assembly and replaced with the new one. The door works good now. Make sure you replace both peices as they will both be worn.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from burns, TN
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
cam riser broke and needed replacing
Just remove all items in door shelves, remove screw holding top hinge cover on. Remove two bolts holding top hinge and remove hinge from door. Carefully open door and lift out of bottom hinge. Remove screw holding bottom hinge on door and replace broking cam riser. Reinstall door in reverse order and adjust top hinge where both doors are even across the top. Thats it!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vickie from Chandler, OK
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Refrigerator hinge broke
Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bowie, MD
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Both Lower Door Cams Worn Through.
Part no. Ps290199 received matched part no. Ordered, which I obtained from your web site, however, part did not exactly match oem part. It was necessary to drill a new top hole in each of the hinges. New hole center was drilled 1/2" off (lower) then hole in supplied part. Jpb could have been accomplished easily by the avg. Homeowner, but the drilling required a little more skill & possible some tools that an average homeowner does not possess. Otherwise job was relatively easy and satisfactorily completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from Charlotte, MI
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer door opened too far due to cam being broken.
I had to remove the top hinge of the door and shut off the water supply to the automatic ice maker. I then unhooked the water line and pulled it through the guide as I took the door off. Once the door was off, I removed one bolt with the nut driver and replaced the cam. I reversed the above actions and replaced the door. It is very important to adjust the door so the seal fits tightly and evenly all round the door. It was a relatively simple procedure that went very smoothly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from New Berin, WI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door closing cams on door hinges cracked and sheered off. Door sit low on hinges.
Just watch the Parts Select YouTube videos on replacing the door hinges. That helped a lot.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Charlotte, NC
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Door would not shut by itself any longer
The on line "how to" video was PERFECT! I followed the steps and the repair was a breeze. Parts Select is now bookmarked in my favorites! These guys make is SO easy for "non-handy" folks like me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Manhattan, KS
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Closing cams were broken
1. Unscrewed the top screws with a socket set 2. Took door off of refrigerator 3. Unscrewed hinge assembly 4. Put on new hinge assembly 5. Replaced door on refrigerator 6. Screwed top screws back in I watched a youtube video on how to replace it that was extremely helpful. I am not a handyman, so if I can do this, anyone can.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J T from Muncie, IN
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Door hinge on ref. side worn out,
My job pretty much paralled the no. one on this list,I am a retired industrial electrician and have many years experience doing similar jobs.Went very well. . Tom Pennington of Muncie Indiana
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Los Angeles, CA
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
rt hand door wouldn't stay closed by itself-door sagged
This door was a problem for 1-2 years before I realized it had dropped about 2 inches. On close examination I saw that the hinge parts had completely broke down.
Had original manual-looked up model # on line under GE appliance and was surprised to find a large complete parts dwg showing parts I needed. Decided I needed the hinge assy.
Removed the door cap on top,replaced hinge assy and remounted door in reverse.--Works like new.
Had original manual-looked up model # on line under GE appliance and was surprised to find a large complete parts dwg showing parts I needed. Decided I needed the hinge assy.
Removed the door cap on top,replaced hinge assy and remounted door in reverse.--Works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Stanfield, OR
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Self closing hinge cams wore out and broke
Emptied door shelves and removed top pivot hinge bracket. lifted door of lower pivot and set aside.
Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.
Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.
Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.
Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Southlake, TX
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom door hinge replacement
Part Number: PS290199
1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.
1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Surfside Beach, SC
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Door wouldn't stay shut. Cam riser was broken.
Emptied contents from the door. Removed top hinge cover (one screw) and top hinge (two bolts.) Lifted door off and replaced broken cam riser on bottom hinge. Put door back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jarvis from St Robert, MO
- Parts Used:
- WR02X10140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
One cam riser on the bottom of the fridge door broke.
Remoed bottom hinge and replaced broken cam riser. Replaced Bottom hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tuttle, OK
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door would not close
I was by myself so I took the entire Fridge door off. Took off the old hinge assembly and installed the new hinge assembly. The process took about 10 minutes and worked like a charm. Door closes like it did 15 years ago.
Was this instruction helpful to you?
Thank you for voting!