GLM23KESBGS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Winston from Ford, VA
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water dispenser would not dispense.
I watched the Video on partselect website for replacing the Solenoid. The repair went smooth. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clyde from San Antonio, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper in door for ice dispenser would not close.
I repaired IAW the PartSelect video. Very easy. One thing that should be mentioned in the troubleshooting process, is to check the retention spring on the flapper. That spring could come off and also cause the flapper not to close.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Plainfield, IL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispensing Door would not close
Not only was your parts selection very easy to understand,
The Video shows exactly how to install that part.
This was So Easy to repair. I thought I would have to take
the door apart from the inside but the repair was completed
with the door closed and took about 10 to 15 min. to complete.
The Video shows exactly how to install that part.
This was So Easy to repair. I thought I would have to take
the door apart from the inside but the repair was completed
with the door closed and took about 10 to 15 min. to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Montgomery, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispenser door would not close after use
I followed the directional video on "PartSelect" website. The video was very easy to follow and showed exactly how to easily replace the dispenser door solenoid assembly. I knew it was the solonoid assembly because the I could see the plunger that controls the opening/closing motion of the dispenser door sticking inside the old solenoid. The "PartSelect" website is very user friendly and very easy to use. The part ordered, delivered by standard delivery, arrived the day after it was ordered. I only wish all repairs could be as straight forward and easy as this one, thanks to "PartSelect" and some limited mechanical/electrical knowledge on my part. This was absolutely a "do it yourself" repair at a very significant savings over using an appliance repair service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from north port, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice flapper would not close
Removed front display and solenoid 3 screws and replace. Clean and install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Croton on Hudson, NY
- Parts Used:
- WR62X10055
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice maker freezing up and not dispensing cubes
I tried to follow the video...it looked easy enough to do and would have been if the trim came off! I had to go to the reviewer who said to undo the 3 springs under the keypad (found on the white part behind the touchpad). I just took an eyeglass screwdriver and pushed up...it was easy to follow the solenoid installation video from there! If I can do it...anyone can! I'm a 65year old female.
Was this instruction helpful to you?
Thank you for voting!