PSM27NHMAWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- huan from garden grove, CA
- Parts Used:
- WR62X10055
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Some screws was rusted so I take more time.
I just follow to the video and take step by step. It's was very helpful and easy. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from millington, MI
- Parts Used:
- WR60X10185
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
cold only in lower part of refrigerater
follow repair viedo
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Savannah, GA
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker door was not closing. Snow piled up enough to fall when door was opened.
Turned power off at breaker. Took off front panel on the door. Unscrewed the panel where the electrical parts were plugged in. Then you could unscrew the old solenoid assembly and install the new one. Cleaned around the Ice shute since some mold was there. Put all back together. We watched the video from you tube about 5 times!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Montgomery, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Door ice dispenser completely frosted up; no ice could get down the chute
Googled the symptoms online and found the great video from Parts Select. My recommendation is follow the video and the rest is easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herold from San Jose, CA
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water dispenser is not working but Ice maker is.
I followed instructions from a video. I pulled off the front panel, then the circuit board unit. Next I removed the Solenoid Assembly and installed the new one. I replaced everything and tested the water dispenser with no success. I assume the solenoid assembly was ok so therefore I need to get the circuit board tested.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary R. from Ocala, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice door would not open or when manually oppened would not close.
exactly as described in your video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bertha from Dugger, IN
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
problem with dispensing ice from door
Watched the video, did exactly as it showed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LAGUNA NIGUEL, CA
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer "flapper" would not shut causing condensation
I reviewed several You Tube repair videos. Not all of them were correct even though my model and brand were specifically mentioned in the videos. Use You Tube with a grain of salt. After sifting through the you tubes, I distilled the information by looking for consistencies. The most inconsistent information was on how to remove the plastic bezels. Once that was figured out, the repair was very easy. Upon removal, I inspected the solenoid. It was very rusted and was no longer capable of pulling the mechanism closed after it had (successfully) opened the flap. The new solenoid fixed the problem in a flash.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Algonac, MI
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice shoot flapper door was sticking
Gentlemen,
Many thanks for the help in repairing my GE refrigerator. From the web site and videos, I determined the problem with the flapper on my ice maker was a bad solenoid. I ordered the part from you then followed the step by step instructions to install it. It made what seemed to be an intimidating job rather easy.
Thanks again,
Gary Schafer
Many thanks for the help in repairing my GE refrigerator. From the web site and videos, I determined the problem with the flapper on my ice maker was a bad solenoid. I ordered the part from you then followed the step by step instructions to install it. It made what seemed to be an intimidating job rather easy.
Thanks again,
Gary Schafer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lee from Frederick, MD
- Parts Used:
- WR60X10185
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Freezer was not keeping food frozen
The problem began when freezer thawed and could not keep food frozen. Initially, I thought the issue was the defrost heater (because I had seen similar symptoms previously and resolved the issue with a new defrost heater)and I replaced that part with a spare that I had puchased previously. The issue was still unresolved and I noticed the evaporator fan was not running in the freezer because it would not turn on when I closed the door. I checked to make sure I could hear the compressor working (and it was)and concluded that the evaporator fan motor was not running. I ordered the part and found a YouTube DIY video on how to replace it. While I was at work, my fiancee took it upon herself to watch the installation video and install the new evaporator fan motor and all is well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Cap May, NJ
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Solenoid plunger rusted and did not reset when not energized so the dispenser flapper would stick open.
Took apart freezer door dispenser mechanism and replaced solenoid assembly in its entirity. Easy fix once the fix to the problem was identified.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Beaufort, SC
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper Door was not opening wide enough to allow ice to flow down the chute. The flapper door was staying open with ice jammed in it.
Contrary to the visual instructions I could not remove the frame around the control opening nor did it turn out need to be removed. The control panel was easily removeable with a small screw driver inserted in the two outer holes at the bottom. Once this was removed I removed the four screws removing the panel with the chute and giving access to the solenoid. The three screws holding the solenoid were rusty and I applied some liquid wrench on each to help with the removal while I cleaned around the area. The solenoid was easily removed but the screws needed replacement which I obtained at my local hardware. Once the solenoid was attached again I replaced the other parts as they were removed and the flapper door is now working as it should. It took all of about 15 minutes for the repair but two days to figure out I did not have to remove the opening frame. Somewhere in the "Repair Film" it should be mentioned that for some Models removal of the "Opening Frame" may not be necessary just proceed to removing the Control Panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Croton on Hudson, NY
- Parts Used:
- WR62X10055
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice maker freezing up and not dispensing cubes
I tried to follow the video...it looked easy enough to do and would have been if the trim came off! I had to go to the reviewer who said to undo the 3 springs under the keypad (found on the white part behind the touchpad). I just took an eyeglass screwdriver and pushed up...it was easy to follow the solenoid installation video from there! If I can do it...anyone can! I'm a 65year old female.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Idichandi from Coppell, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Ice maker door was not closing.
Changed after watching U-Tube instructions. Faced trouble with the magnet assembly, had to redo it again, and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Lake Worth, FL
- Parts Used:
- WR60X10185
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Fan motor sounds like howling wind
I followed the video provided by PartSelect, very helpful. I had to cut and splice 4 wires. The repair was successful. The replacement part was an exact duplicate of the original. I still notice the same sound but one tenth the volume. I hope the problem does not return. Many thanks to PartSelect for information to identify the problem and prompt shipping of the repair part.
Was this instruction helpful to you?
Thank you for voting!