GSA20IEPDFWW General Electric Refrigerator - Instructions

After figuring out how to remove the old broken clip, replacement was easy. Had to use a small putty knife to open the release on the bottom underside of the clip(between the clip & the refrig) . By looking at the replacement piece it was easy to figure out.

Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.

look very carefully at the picture you provided in the parts fish, removed the ice maker tray and the rest was very easy ,i saved alot of money and time doing it myself.

My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.

Replaced flapper

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

i used the video it showed on the site or iwould not have been able to do it

I recieved the new ice bucket, I took out the old ice bucket and put the new ice bucket in.

I replaced that part, but I still have the same problem, no water is dispensed. I believe I may need a circuit board. The problem was not the parts I replaced.

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

Removed the ice tray and then the auger unit from the tray assembly. To accomplish auger removal, the auger assembly is attached to the tray assemble at the front. On the front bottom there two screws. Back them out. Then on the top of the tray assembly the auger assembly is held in position by two tabs. Depress them with a finger or thumb. Do not use a screw driver as this may result in breaking the plastic tab! The auger assembly will separate. The crusher plate easily separates from the auger assembly and is removed buy "spiraling" the plate up and off the auger itself. Simply reverse to install new plate.
Recommendation: Take this opportunity to thoroughly clean and COMPLETELY DRY all components prior to re-assemble and re-install into the refrigerator.

Watched video, however could not get outer casing off. Under the panel are three small holes, pushed up with an Allen key, used a small screwdriver to wedge out, came out easily, followed instructions from video on removing and replacing solenoid

Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.

Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.

i removed srews from area until i could access the fan unit and removed it. wires were not identical so i had to splice some together, most likely could not have been avoided. the exploded parts diagram helped me to be sure that i would have all replacement parts on hand so i wouldn't have to wait for something i had forgotten.