ZIR301NPPBII General Electric Refrigerator - Instructions

I shut the water supply and took off the rear panel.
One screw released the valve. Pulled off water lines(3) and electrical connectors and installed all on new valve. Screwed the valve and the panel back and turned on the water supply. Prior instructions on website helped. Part came in two days. This part should have never failed. Looks like the housing is two parts glued together. Glue failed after 7 years. G.E. should cover this. My warranty expired after 5 years. M.K. Boca Raton,Fl.

After gaining access to the back of the refrigerator. I shut off the water valve and pulled the electrical power plug. I removed 6 screws from the access panel. I then removed 1 screw holding the water valve. I disconnected the electrical connectors. Disconnected the water inlet tubing with an adjustable wrench. I removed the water to the door and water to the ice maker by pushing in on the collar which released the tubing. I discarded the old valve and installed it in reverse order. Did not fix the problem. My next guess is the control module.

replaced double outlet water valve. Valve works as it should. Shipping was much quicker than I expected.

Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!

pullee refrigerator out to get to back un pluged power took off back cover unscrewed one screw to loosen water valve unscrew water inlet line ther are two water lines in back of water valve i cut them as close to water valve as i could push the water lines that i cut off into water valve makin sure in the rigfht place they are quick disquinect just push in and ther on screwed water valve back on connected water inlet line replaced back cover pluged in power pushed refrigerator back in and was done it had to run for a little while to get the air out then worked fine

I turned the water off at wall. Then I removed 6 nuts removing the back cover. Removed one nut to remove the outlet water valve. Disconnected two bottom hoses and put them on the new unit. Removed top hose and installed on new unit.
When I removed the top hose water did spill out.
I had to rush to connect it to the new unit .

Easy repair. Diagnosis was tricky - this website and popular mechanics article helped me to narrow down the problem to the solenoid water valve.
Unscrewed the left side of the back panel and unscrewed old water valve from its bracket. The steel inlet hose was easy to disconnect, as were the two electrical socket connectors. The two outlet water hoses to the refrigerator were a little trickier. You need to cut them with a blade, and insert them into the new valve, which has teeth to hold them in place. Once I figured that out, the rest was easy. I remounted the bracket, and then tested the water flow successfully. Great website, thanks for the help!

watched your video,went to work

removed rear cover of Frig, found valve was cracked and leaking water. turned off water and ordered new valve. After receiving new valve, Removal and installation took about 15 minutes. Pretty easy, a no brainer.

Unplugged fridge, and turned off water supply. Removed cover from back of fridge, followed the plastic tube down to water valve.
I unbolted the mount holding water valve in place, removed the input tubing on top by unscrewing nut. I made a note of which outbound plastic tubing went to water dispenser, and which one went to icemaker, and which side of the water valve they plugged into, and then cut the tubing very close to the old valve.
I slid the tubing into the new water valve, and I felt it lock into place, very easy. Attached the input water line and tightened the nut.
Reattached the water valve mount to the body of the fridge, replaced cover, turned water valve back on and checked for leaks (there were none).
Plugged in fridge, tested dispenser, everything worked just fine. No leaks.

1. Remove back cover from frig
2. Remove Double Outlet Water valve from frame
3. Place towel under valve, remove supply line to filter
4. Cut black and clear lines next to valve, ensure a smooth cut
5. Slide new connectors onto lines, press lines into valve firmly, make sure they slide in all the way
6. Slide connectors into valve locking into place
7. Re-connect filter supply line and re-connect valve to frame making sure lines are in the proper place
8. Replace back cover of frig, do not over tighten screws

very simple repair.....push two hoses into compression fittings on the bottom, plug two wire harnesses into the back, and put a screw into the front to attach to the refridgerator frame. After that, just turn water back on and plug it in. Ran great.

Part also came in quicker than expected......which was a definate plus.

turn off water remove back cover remove 1 screw holding water valve use wrench to remove main water line input push up holders on bottom of selinoids pull both output lines loose disconnect two electrical plugs reinstall new valve in reverse order

Removed back panel. Cut the water lines and replaced the double outlet water valve. The only issue was the long period of time until the water flowed from the outlet. Be prepared to wait, it will take some time for the water to flow.

After confirming that a frozen water line was not my issue, I confidently bought this item and installed it within minutes after receiving it! It is easy to install - just close the connection to your refrigerator, open the rear lower panel, disconnect the water tubings and electrical connectors. Reverse that - you have the installation. Plug the refrigerator back on, turn the water back on for the refrigerator - and observe for any leaks. If no leaks - try dispensing water. Working great for me! My refrigerator's model is a GE, model # zfsb26dnass.