TFJ22JABCWW General Electric Refrigerator - Instructions

As suggested by your web site. Thanks. BC

Followed the video to replace bottom hinge assembly. The only hiccup was that the video instruction was for the fridge side door, so there wasn't step by step instruction for dealing with the electrical connection at the top of door or the water line at the bottom. However, it was simple enough to figure out. Replacement took about 20-25 mins.

Empty all the good stuff stored in the door. Remove top hinge, lift off door. Remove bottom hinge from door and refrigerator, replace with new hinges. Replace door and reinstall top hinge. Very simple. Worst part was removing all the stuff stored in the door then putting it back! My parts arrived very quickly and I'm very pleased with Part Select.

Watched PartSelect video and did exactly as video said. Had finished product in less than 30 minutes.6 bolts and one screw.

Removed top hinge, lifted door from bottom post. Removed post with nut driver/socket, removed corresponding bracket/receiver from door. Attached new parts to refrigerator base and bottom edge of door. Was careful to replace part pieces in the same order as original, and secured tightly. Lifted door onto bottom hinge post, leveled the door and replaced top hinge.

I watched the "How To" video on the Parts Select web site twice. The video was very helpful, kind of like having someone right there with you showing you how to replace the hinge. I emptyed the door shelves, removed the top hinge hexscrews and easily lifted the door off the lower hinge, pieces of the broken cam hinge on the door fell off. I set the door on the floor in front of the sink with the handle edge on the floor. I unbolted the hinge and installed the new one. I loosened one screw on the door cam hinge and removed the other, easily replacing the broken part. Before tightening the screws I checked to make sure the hinge hole in the door was not blocked by the new cam hinge. I lifted the door and water ran out from somewhere. I tried to set the door on the lower hinge several times with no luck. I rechecked the hole, it was still clear. I tried placing the door on the refrigerator using the seal to hold it in place, that worked but I couldn't get the door to drop down onto the hinge. I played with it some more and finally got it in place, reinstalled the top hinge, mopped up the water and tried the door. It didn't self close. I adjusted the top hinge a couple of times and applied a little silicone to the hinges, it still didn't self close. I told my wife to make sure the door closes completely and reloaded the stuff into door. After a couple of days it now closes by itself like it's supposed to. In retrospect, I was alone doing the replacement and it really was an easy job but a second person to help line up the lower hinge would have helped a lot.

Noticed hinge cam riser broken in 3 pieces. Took fridg door off, 3 screws on top. 2 screws on bottom loosend one screw and removed other screw. replaced cam riser and reassembled. Wife helped.

Several months ago I had to replace the hinge and cam on the refrigerator door and the repair went smoothly as pictured in the video. This time I had to replace the cam on the freezer door so I ordered the hinge assembly, which included the cam. The web site confirmed that, according to the model number of my 27 year old refrigerator, the hinge assembly would fit. The problem I had was that the top hole in the hinge was positioned too high to fit the hole in the refrigerator so I had to put the old hinge back on, even though it showed some wear. The door closes smoothly by itself now.

Removed freezer door, put a blanket over the opening to keep food frozen. Installed hinge and replaced door.

on the refrigerator side remove two screws from hinge on top of door, pick doorup to remove from bottom hinge using a 5/16 socket remove the two screws holding hinge in place, replace with new hinge. on the door loosen up the screws, no need to remove. the screw closest to the hing axis remove completely remove the old cam, insert new cam lined up with axis of hinge reinsert screw, place door back on hinge and replace hinge on top. the freezer side has water an ice in the door.at the bottom [grill has been removed] of the door a plastic tubing has to be disconnected [make sure water is off] the disconnect is near the door, the coupling is only finger tight. uncou[ple plastic coupling and pull out of connection, pull the nut and ferule off the tubing. now take top hinge off, remove door straight up while feeding plastic tubing thru hinge. the hinge is replaced the same way as the other side. when new hinge an cam are in place, lift door up now feed the plastic tubing thru the hinge till door is in place, replace top hinge. when you reconnect the plastic tubing it helps if you place a lubricant on the end so that you slide the nut and ferule on. the connection should only be finger tight, no wrenches

shimed the door up to its proper level. removed plastic cam from bottom of door with a socket disconnected the water line fitting and clamp. with a nut driver removed the hinge assy from cabinet being careful i sled the hinge assy off the plastic water line being sure not to kink the line, sled the new hinge assy back on the water line and mounted the new hinge assy to the cabinet and connected the water line back up and turned on the water and checked for leaks, all went well. place the bottom grill cover back on.

Followed directions in your video. Very helpful. Be certain to pay strict attention to how old part is removed. Had a little trouble replacing door on lower pin/hinge. Helps to have a little assistance. Good suggestion from another customer: get the kit.

Repair was exactly as described on U-Tube video. The whole process, including removing items stored on the refrig door, took around 20 minutes and involved only a screwdriver and one socket. Could not have been much easier. Dont know why I delayed fixing what had been a long term annoyance.

MY issue was a old worn out hinge cam on the right side door of our 1993 GE Profile Refrigerator. My repair went great- exactly as depicted in the PartSelect You Tube video: 'Refrigerator Repair- Replacing the Hinge Cam Riser (GE Part # WR02X10140)' Excellent video! Having the PartSelect on line video demo gave me confidence to buy the part and "just do it" to make the replacement. Watching the video confirmed my own assessment of the (very simple) repair procedure, and eliminated my wife's fear that I would remove the 19 yr old refrigerator door and then not be able to put the door back in place! I ordered two WR02X10140 hinge cam parts so I would have a spare. I know we need a new more energy efficient refrigerator, but our GE Profile is still fine for our family. This hinge cam replacement will give my wife more time to make a well researched decision on our next refrigerator purchase! You made me a 'home hero husband'. Great job- Thanks!!!

replace the lower door hinge assy. and closer cam as a set.Only used a 1/4" socket and ratchet.The process was very easy without any problems.