MSK28PFBBAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from Medway, MA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
ice maker not calling for water to make ice.
I removed the screws that held the unit in place, and also the screws that held a plate that covered where the unit plugs in. I unplugged the unit, and removed it. Put the new one in, reversing the steps. Turned the new unit on, and had ice in 45 minutes! Summer is coming, I need my ice maker! This is the second unit I have replaced on this refrigerator, the first one was not releasing the cubes. This second one was a different style than the first, but same install process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark J. from Alice, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker quit working, I took it apart and found a broken wire at the thermostat, soldered it back, but apparently it got too hot.
It took longer to remove the ice bucket and frozen food than it did to replace the ice maker. Remove one screw with a 1/4" nut driver, slide outward and remove plug. transfer water tube to new unit. plug it in, slide into rear slots and install one screw. Replace ice bucket and frozen food, shut the door and hear ice falling in about 30 min. Easy job! Great product! THANKS MJS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Georgetown, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our icemaker quit working.
My husband took the old icemaker out before the new one came in. When the new one arrived, I installed it in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Hanna City, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker would not work.
Removed the Ice maker from the freezer because the light was not on. Disassembled ice maker, found printed circuit board had shorted across two posts because the board was black in that area. Bought new ice maker assembly, installed in less than five minutes, making Ice fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HERBERT from Harlingen, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket was shot
took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Atlanta, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost was building up inside the freezer just above the ice dispenser shute.
Followed the instructions and replaced the door recess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Arlington Heights, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost on the bottom of the ice bin frome warped rubber flapper
Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from MITCHELL, IN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Icemaker Wouldn't Totally Work
Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from zion grove, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rubbeer flapper was worped causing frost in the freeze
The same as the vidio, very easy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Northville, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old ice maker quit
removed old ice maker, obtained part number from it. went on line ordered new ice maker at 10:45 in the morning, at 3:00 the nexte after noon new icemaker was in hand. took about 5 minutes to install new ice maker. works perfect. would do business again with this company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Brooklyn, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
My Icemaker arm was broken. It didnt move up or down by itself.
I removed the ice tub. Removed the screw on the left side that holds closed the section where the icemaker plug is connected. Disconnected the plug. Then removed the bottom right screw. I was then able to remove the Icemaker by unhooking it from the bcak freeze wall. I disconnected the icemaker from the fan gaurd. Removed the icemaker cover. unscrewed the 3 icemaker screws and opened up the chamber. removed the old Ejector Blade Drive Cam by removing the outer srew that hold the gear to the icemaker. changed the cam with the new one and reassembled everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Pittstown, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice chute from the ice maker frosted over. Cubes would not dispense
1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Darien, CT
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped working; would not fill
It was as easy as the instructions were clear (and they were). Remove 2 screws and two nuts, pop out the old ice maker, pop in the new, plug in and tighten screws/bolts. It worked. I'm happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Bismarck, ND
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Take out old ice maker and replace with new
Used the nutdriver to loosen two screws, life out ice maker, disconnect electric plug and put aside. Placed the new icemaker on the loosened screws, plugged in electric connector and tightened screws. Used small level to verify that unit was level.Waited about two hours for first cubes to be released into tray - has been working fine since!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Mattoon, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Icemaker quit making ice.
The parts were here the next day. After removing the old ice maker it was a simple installation using the adapter cord furnished. It took about 15 minutes. You have to work with the cord some to get it to fit behind the ice maker, but it does fit. The ice maker started up immediately & works great.
Was this instruction helpful to you?
Thank you for voting!