GSS25IMNWHES General Electric Refrigerator - Instructions

Clear freezer items in the area of repair as light assembly is in the back of the freezer. Suggest removing shelving in the same area to provide more working space. Utliize a small flashlight to provide interior lighting. Use a stubby phillips screwdriver to remove fastener securing the light cover.
Cover snaps out to remove light board assembly. Gently pull to disconnect the electrical connection to the light board. Then pull the light board assembly from the mounting posts securing the light board. Be careful not to snap either posts or the light board.
To install the new light board, I found it easier to connect the electrical source first, then push the light board onto the plastic posts to secure the light board. There are holes in the light board to insure a secure fit. Reinstall the light cover and reinstall the mounting screw. All done in less than 5 minutes!

Simply removing parts from the old frame and installing them on the new frame and putting everything back in the refrigerator to include the glass.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.

Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

Ordered gasket. Laid out gasket near sunlit window untangled and flat on carpet for 24 hours to insure it was pilable and correct shape. Removed the old gasket manually easily without any tools and cleaned the door's seal groove with a paper towel slightly soaked with Simply Green. Installed new gasket starting at the upper corners then inserting upper edge by tilting the gasket toward the inside of the door with my fingers. Then installed the lower corners along with the bottom edge. Proceeded installing the side edge working from the set corners inserting the gasket's inner tongue into the door groove with my fingers again tilting the gasket inside the door. Once the gasket was installed, I closed the door and guided my fingers along the gasket to insure the magnetic edge formed a firm seal. This is wear the DIY videos suggested applying petroleum jelly but I did not need it since the gasket was pliable enough. Overall, the effort took 15 minutes because I think laying out the gasket for 24 hours allowed it to settle into its desired form..

Installing the part repaired the fridge and freezer immediately.

It was so much easier than I thought. First we used a hair dryer to loosen everything up. Just pulled off the old on (with our hands) and put the new one on. Then went around the edges and wiggled it into place. There are plastic ridges that if fits into, so it’s important to make sure every part is sealed.

I made my wife fix it.

replacement part was not identical to the original. Mounting screw sockets did not exist on replacement part. I still used the new part but it is held in place by gravity (no screws). New part works but must be treated gently or will break like the original or fall out of place. Part diagrams online were not adequately clear. It would have been good if photos existed of the replacement from assorted angles, and I would have seen the lack of mounting screw sockets.

FOLLOW INSTRUCTIONS OF YOUR VIDEO

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

Super easy. Hardest part was popping the plastic covers off without breaking them. I had to use a butter knife to get under it & lift it just enough
to grab it & pull easy until it turned loose.

We opened the box, unpacked the drawer, washed and dried it, installed it! No muss, no fuss!