TBX18CIBQRCC General Electric Refrigerator - Instructions

Installing the actual ice maker was quite easy. What takes most of the time is preparing the freezer for the install. Need to remove all shelving, (and the door) to gain access to the unit. The ice maker is simple to install once access is achieved. Putting everything back together takes some time.

Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.

I ordered a new micro switch that was activated by the high ice lever. Once the switch was replaced the ice maker cut off as it should have and stopped producing too much ice. YHis job was of moderate skill level, the most challenging was replacing a spring that popped out then reassembling the unit.

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!

The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.

I watched the video from the link that was sent to me with the shipping notice. It was very easy to understand. I had no trouble at all. I'm 75 years old woman, however, and I can fix about anything. Don't be afraid to fix appliances yourself if you feel you have the knowledge.

I'm a housewife in her late 40's. Before ordering the part, I watched your video on how to remove and install the new icemaker. First I unplugged the refrigerator. After a few minutes, I unplugged the icemaker and unscrewed it. I lifted it a bit and removed it. I did not use the icecup that comes with the part. Instead I removed the one from the old part and inserted it to the new one. Then I plugged in the new icemaker, placed it inside so as to match the holes and screwed it in. YES, it was that simple. It took me less than 10 minutes to do this. I saved myself over $100!!

followed instructions from video on your site

Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen

i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess

Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.

Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....

The repair went smoothly and surpising easy! Get access to the back of the fridge. Unplug fridge, remove cardboard but save to put back in same place. For our fridge it was to bolts removed by socket set, removed old condenser fan motor (applyed a little pressure) and placed the new condenser fan motor in. It's easier with two sets of hands, but I've got to say DIRECTIONS OTHER THEN CUSTOMERS TESTIMONY SHOULD BE SENT WITH THE PART!! Otherwise quite simple.