TBX25PRYCRAA General Electric Refrigerator - Instructions

The entire frame that holds the two crisper drawers pulls right out. After that, it's just a matter of unscrewing the broken part, snapping in and screwing the new part and sliding the whole thing back in.

Remove bottom glass shelf, lift up -then remove entire drawer slide assembly.Remove plastic decorative front cover(it just snaps off) and unscrew left side drawer slide screws.replace with new part and screw in screws. Replace in bottom of fridge and replace glass shelf.So Easy that an average house wife like myself was able to do it alone.Almost as easy as finding the part needed on partselect.com! Thanks, it was much easier than apple pie.

The repair was very simple. The longest part was taking everything off the shelf in the refrigerator so that the slide rail could be removed. Then when things were out, it was clear that the bottom of the refrigerator needed cleaning. The repair itself was done quickly. The cleaning (yuck) took longer! this is a great site because the part came quickly and it was very easy to select just what was needed.

Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.

Removed two screws, lined up the rail and replaced the screws. That was it!! Glass shelf sat on top and bin slid in smoothly.

Ordered an auger, could not put together sent back and ordered whole assembly. Fit like a glove. Parts select gladly accepted parts back for whole unit. Would order from Parts Select again.

remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first

Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.

I watched the Utube video, repeated the process at home while awaiting the part, and installed the flapper door in about 15 minutes after it arrived--piece of cake. The hardest part was removing the escutcheon plate on the front of the freezer door. I figured out I could slide a putty knife under it and the rest of the project was completed in no time at all.

I followed the video instructions to the letter and it was very easy and a total success. I believe I would have had problems but for thr video demonstration which was very clear and straight forward in a simple manner. Thanks for the prompt delivery of the part and the help installing it.

I followed the repair video Partselect provided online. It the repair easy and fast. Great video!!!!

Unscrewed the old rail, cleaned everything and installed the new rail

Followed video. Changing flap was not difficult but did not fix the problem.

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) removed fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.