ZBD6880K01SS General Electric Refrigerator - Instructions

Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!

I moved the dryer away from the wall and unplugged the electrical cord. I unscrewed the 4 screws on the top of the dryer to gain access to the Dryer Rotary Start Switch. I pulled the part out of its set location and carefully removed the clip on wires. I then carefully attached the wires to the exact locations on the new part and put it back into the proper location. I installed the screws, plugged in the power cord and moved the dryer back to its location for operation. I turned the circuit breaker back on. I failed to mention that I turned that off first of all. I set the dryer control to dry and turned the Dryer Rotary Start Switch to on and it worked immediately. This took about 12 minutes totally from start to finish.
Thank you for being there.
Sincerely, John Pewters

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

Removed the 6 screws that held the top panel in place. there are only 3 wires, 2 that go together and 1 single wire.Uplug the dryer,twist out the old switch,twist in the new one, attatch the wires,replace the panel,BAM your done.And the best part of it all the part was right the first time.they make it so easy to get the right part the first time!

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

I unfastened the three 1/4" rear screws, then the two support screws on top. I pulled the old element out,( plenty of slack wire luckily). disconnected it from the bayonet-type connections, then attached the new element. I secured the new element using the 1/4" screws. Bingo!

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

Remove back panel on bottom of fridge to access compressor area. Remove screws from water solenoid and water valve and push to the side so the side of the compressor can be accessed. Then locate the inverter box. You will find a Phillips head screw on the bottom of the inverter. This is the only screw that hold the inverter in place. Remove the screw and tilt the inverter box forward away from the compressor, then lift the box out of the the holder. You may have to wiggle it a bit to get it out. Remove the plug that attaches to the compressor and then with the power on check your voltage coming to the compressor. It should read 120 volt. If it doesn’t your inverter is bad. Remove the other plug on the inverter box and pull the box out.
Reinstall the unit in reverse order. Use the appropriate jumper to plug into the wire connection going to box and then plug it into the connection off the fridge.
Once everything is reinstalled and before you put the back panel on plug your refrigerator back in and you should be able to hear the compressor working or feel the top of it to make sure. If it’s working you are good and can reinstall the back panel.
It will take 4-5 hours to come back to temp if it’s been off for any length of time.

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.