Models > GTR12BAXRWW > Instructions

GTR12BAXRWW General Electric Refrigerator - Instructions

Jump to:

All Instructions for the GTR12BAXRWW
61 - 75 of 701
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
connie from omaha, AR
Parts Used:
WR60X31522
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Fan Motor stopped working
Not only was finding the part rediculously easy for a person who has never done this type of thing...the repair was a sinch!! I will always return to this company for help with home equipment repairs. I saved so much money doing it this way. :) thanks guys!
12 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Hartsel, CO
Parts Used:
WD15X10003
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set, Wrench (Adjustable), Wrench set
Replace valve
Unscrew supply tube and angle nut from old valve. Disconnect tube from valve. Install new valve. Obtain new crimp seal for water supply tube. Use Teflon tape. Reconnect water tube to valve.
12 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from Philadelphia, PA
Parts Used:
WR09X20002
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
malfunction of the cold control (wearing out after 15 years)
1. Disconnected 120 VAC power supply from refrigerator. 2. Removed 2 philip screws from horizonal panel containing the thermostat. (Panel is in refrigerator section). 3. Removed plug module from panel which freed the panel which allowed me to remove panel to do repair. 4. Removed wires from thermostat (cold control), and mechanically removed thermostat from panel and installed new cold control (thermostat). Replaced wires on control. 5. Replaced panel and reinstalled 2 philips screws. 6. time to repair about 15 minutes.
12 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Natalie from Bethlehem, AL
Parts Used:
WR17X11662
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bottom shelf of fridge that holds the drawers in place
I typed replacement fridge parts in google. Parts select.com came up. I found my fridge model # on the fridge and typed it in. A similar model # came up and I looked at the parts diagram. I determined what the piece was. I checked a couple other similar fridge model #'s to see if the part was the same. It was. Parts select made it so easy! I ordered the part on Monday in the afternoon... used regular shipping and had it in my hands by 9 am on Wednesday. I opened my fridge took out the collapsed bottom shelf (courtesy of my forever climbing 3 year old!) Installed the old glass and drawers in the new tray and Voila! as good as new! This couldn't of been a better experience from beginning to end,
13 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Chesterfield, VA
Parts Used:
WD08X10018
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Original gasket was old and had started to dry-rot.
Installing the gasket took about 45 seconds. It actually took more time to scrub the area clean prior to installing. One quick trick I found was to fold the replacement gasket in two, and use that mark to center the gasket and press it in from there. That way you don't have any guesswork as to how much slack to allow for when starting.
11 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Maksim from Falls Church, VA
Parts Used:
WD12X10271, WD12X10401, WD21X10224
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Dishwasher did not start
The repairman diagnosed the problem as a control board failure and quoted a $350 bill. I self-diagnosed it as a failed interlock switch -- and found out that the switch was OK but the cover was cracked, preventing the switch from functioning normally. Total repair bill - $1.50!
11 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paulette B. from Santa Ana, CA
Parts Used:
WR2X9391
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Light in the refrigerator went out
After I bought what I thought I needed for the repair. I asked a friend to come over and look at it. He changed the
the light socket and put the same light bulb in and it works great. I am returning the light switch but decided to keep the light bulb.

Getting on the internet was so easy. This was really very simple. Thank you for making what I thought would be a big ordeal into something very simple.

Paulette Johnson
13 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gabriel from La Mesa, CA
Parts Used:
WD28X10391, WD28X25960
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
The wire cage began rusting
The bottom rack just pulls out so that was an easy replacement. The upper rack required a 1/4" nutdriver to remove the sprayer from the rack and a slot screwdriver was used to remove the tab that was holding the rack to the slide arm. Total time, 10 minutes tops!
12 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROBERT from ALBANY, NY
Parts Used:
WD15X10003
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Broken Inlet valve
Disconnect electrical power & shut off water supply. Remove front panel covers. Removed mounting screws (2). Unhooked water supply line & flow line. Took off old brass adapter fitting. Teflon taped fitting to new inlet. Performed reverse procedures. It ran just fine!!
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kirk E from GRASS VALLEY, CA
Parts Used:
WR55X24064
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Fridge keeps cycling on and off and a clicking sound happens every time compressor cycles.
I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I searched and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.

Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.
10 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Somers Point, NJ
Parts Used:
WR23X37285
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Switchlight was broken on tennant's refridge
as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
paul from dahlonega, GA
Parts Used:
WR17X11662
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Vegetable shelf frame broke
Took out the broken one and put in the new one just as the vido showed me how to. Took about 2 minutes.
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tom from Bethesda, MD
Parts Used:
WD18X10008
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
The cat brought in a rat which ate holes in the sump inlet.
First, I took off all the pipe clamps and retaining brackets. Then, I pried it out of there. One of the tabs holding one of the other bits to the body got busted, but it didn't matter, as it is held on very well just by the pipe clamp connection. I stuck the new one in and re-attached all the hoses. The GIANT complication was that a new floor had been installed over the old floor, right up against the kick plate- so in order to remove the dishwasher, I had to slice open the counter, as the new floor prevented sliding it out. To prevent the problem recurring, I spray painted over the sump inlet to make it taste worse. This is the downside of a cat door.
11 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from Demorest, GA
Parts Used:
WD08X10059
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Seal was broken
Took screws out of door. Slid bottom seal off and slid new one on.
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Floral Park, NY
Parts Used:
WR60X31522, WR02X10540
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Evap Motor - loud noise
The evap fan, based on research, appears to be built to only last a few years. Pay attention to your order of removal for all pieces and it will go back rather easily in reverse.Remove items from freezer. UNPLUG FREEZER. Pop out the shelf. Use screwdriver to remove plastic piece in back. Pop out styrofoam piece. Use screwdriver to remove back metal section of freezer. Use nutdriver to remove screws holding the fan to the back. Unplug the motor. Pop off the fan. Pay attention to location of all these pieces. Put them on the new motor. Reassemble in reverse. Piece of cake.
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTR12BAXRWW
61 - 75 of 701