PDS22MBRBBB General Electric Refrigerator - Instructions

Easy

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Removed circuit board cover, unplugged l
Leads, rePlaced board, leads and cover. Done

Also watch the video. Super simple

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

removed cover from rear of refrigerator. disconnect mother board connections. Unplug first, used needle nose pliers to squeeze plastic tabs holding on motherboard and replaced old with new and plugged back in connections. Plug back in refrigerator and done.

Cleaned mating surfaces with acetone using vapor mask because done indoors. No instructions as to which cleaner to clean old glue off. Matting surfaces. No nistructions as to what glue to use so used silicone. We'll see if it holds up

I wouldn't have had a clue without your video. After the part was delivered, which was only in two days, I watched the video. The man explained everything perfectly, making our "fix" a breeze. It was great, I stood over my husband's shoulder, while he sat on the floor and told him what to do step by step. It couldn't have been easier. You guys are awesome!

Very simple fix by replacing the mother board. Your "how to" video made the repair even easier. The appliance repair estimate was over $400. I saved over $200. I already recommended your site to several other people. Thanks for making it so easy

I easily removed the screws and then removed the board and took a picture so I would remember how to re-connect it. It was really easy and now my refrigerator is working great. If I can do it anyone can do it. My husband was amazed that I did it all by myself.

Used 1/4 nut driver and drill to take off acc pnl. The repair amounted to unplugging several connectors, removing the old motherboard, installing the new board and reconnecting the wires. this solved the problem and the whole appliance seems to run better.

according to the vidio showing how to to change the control board its look relatively easy i dont think i will have a problem changing it ,,but will i change the right part for the problem " the frige take to long to get cold again after thrawing state freezer temperature went up to 19 * or more sometime ,,thermostat has been changed and its solved the ice deposit problem" hopefully changing the control board will help shorting the long thrawing state" the board has not been changed cause the frige start working again

I ensured that the refrigerator was unplugged from the power, removed the main board enclosure cover, carefully unplugged the wiring connectors from the board, released the 4 plastic standoffs with needle nosed pliers by gently squeezing the ends and removed the board.
I placed the new Main Control Board on the standoffs, carefully re-connected the electrical connectors, ensuring that the plugs were mated correctly, replaced the board enclosure cover and powered up the refrigerator to verify operation of the compressor, fans and controls.
Once verified, I unplugged the refrigerator from the power, removed the access cover to the compressor and condenser and carefully cleaned all dust and lint from the back and underside of the refrigerator before replacing the cover and putting the refrigerator back into service.
The cleaning will improve the efficient operation of the refrigerator.

Checked this website for symptoms described, found same descrip, ordered mainboard, changed out in less then 30 minutes, Frig working properly now. Follow the installation instructions carefully as this mainboard fits other frig's & depending on model some wires need to be cut on harness etc.

first empty both sides then took apart freezer area ice maker-light cover-back cover and exposed fanchecked all connections ordered fan[had no amp probe to see if power at motor repaceed fan still fan didnot runmoved fridg out from wall found control board didnt find any thing wrongto the eye ordered control board remove all connectionsused plyers be easy to remove from board squezed little whit tabs[3 or 4] to remove board from fridge installed new board snapping the pegs back into holes then reinstallwire connectors [ps the board comes with a few extra ports dont worryjust connect to the ones on the old board] dont forget to hook up green groung wire when you put cover back on then plug in and turned on closed up the freezer and reinstalled icemaker and other parts started and all seems ok good luck

Unplugged side by side took about 4-5 screws out removed plate from back, unplugged the wires removed old board and plugged wires in new board, note: new board a little different than original. Screwed plate back in. So far so good. I do not think I will buy any more ge appliances, this one was very expensive but out of warranty now my ge dishwasher is making noise all purchased at same time.