XSS23GGKRCWW General Electric Refrigerator - Instructions

Removed the lower 2 drawers, lower front grill, rear lower compressor cover. Removed the 2 water lines from the quick connects and screws from the water tank. Pulled lines through the hole in the right rear of the refrigerator and removed tank. Then reversed steps to install new tank. The upper plastic tank cover has 2 buttons on top that are really screws with a plastic cap, these are easily removed with pliers.

1. Emptied the crisper pan,
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.

Very easy repair, 3 screws to remove motor assembly and 3 screws/1 nut to remove motor from housing. Reverse order to replace. VERY EASY repair!

Used a putty knife it pry off old switch, unplugged old switch from wire harness, replaced new 1 in, snapped back in place. Took about 2 minutes.

Opened package and just snapped in front insert. Took longer to open package than it took to replace broken insert.

Removed broken switch with plastic scraper (press tension latch on bottom), moved two wire terminals to the new switch and pressed the new switch into the hole.

Very easy novice could do

I was able to snap the new piece right in

Followed instruction video. Replaced water tank, flushed line from house water. Reconnected line and cycled until tank filled. I have ice and water now.

NOTE:You can still use your Ice Maker as the water tank is for water dispenser only-only leaked if you pushed on water dispenser;We put painters tape over water dispenser until we got our water tank (Part# PS783769);easy install see below ;NOTE - WATCH VIDEO ON HOW TO INSTALL -ALTHOUGH NOT THE SAME UNIT AS MINE THE PROCEDURES ARE SIMILAR - A MUST
a. Remove food from bottom 3 drawers in refrigerator side so you can remove the drawers to access Water Tank
b. Turn off water
c. Take cardboard off back of Frig (bottom of Frig)
d. Find tubing (short one) that goes to water tank & remove where it connects to the union:located Left side bottom of back of Frig - Push in white lip to remove tubing
e. Remove grate from front of Frig (on bottom) removing 2 screws one far left & one far R (will have to open doors)
f. Find long tubing from Water Tank left side under Freezer door and pull out where it connects to union so you can work on it with Freezer door closed - Disconnect tubing by pushing in on white ring on Union to release tubing.
g. Removed 3 bottom drawers Frig side
h. Removed plastic guard from over light (just pull up on both ends to remove (16 1/2 in long)
i. Remove plastic over top of water tank
j. Remove foam from over top of water tank (be careful not to break foam
k. Take out 2 screws holding water tank
l. Pull out Water Tank and Tubing noting which hole short & long tubing comes out of
m. Install new Water Tank by pushing tubing into holes; Short goes in right hole & Long in left hole
n. Attach Water Tank with two screws you removed, attach foam, plastic cover over Water Tank then plastic over light
o. Short tubing will come out toward back and long hose needs to be pushed under frig toward front freezer door.
p. IMPORTANT NOTE - REMOVE PLUGS FROM TUBING where it connects to Union - I had to undo this part because I didn't notice the plugs
q. Connect Tubing - Short to rear Union by pushing in on white collar on union and do the same with the front long tubing
r. Turn water back on
s. Test Water dispenser to make sure it working before re-installing cardboard on back & grate on front - this is when I found out I forgot to REMOVE THE PLUS FROM THE TUBING
t. Install cardboard on back & grate on front
u. Put in shelves & food back into Frig
v. Because it's quick no need to move food from top shelves

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

My father called and asked me if I knew where he could get a new switch light for his refrigerator. I came across your web site and found the part right away. In less than 3 days the part came and my father put it on. He said it was easy and that it was great to have the part come to him instead of having to search all over town. Thanks so much for the fast, easy service.

Clear freezer items in the area of repair as light assembly is in the back of the freezer. Suggest removing shelving in the same area to provide more working space. Utliize a small flashlight to provide interior lighting. Use a stubby phillips screwdriver to remove fastener securing the light cover.
Cover snaps out to remove light board assembly. Gently pull to disconnect the electrical connection to the light board. Then pull the light board assembly from the mounting posts securing the light board. Be careful not to snap either posts or the light board.
To install the new light board, I found it easier to connect the electrical source first, then push the light board onto the plastic posts to secure the light board. There are holes in the light board to insure a secure fit. Reinstall the light cover and reinstall the mounting screw. All done in less than 5 minutes!

I just moved the moving parts from the Frame for the humidity level from old to new and all was OK

I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" out the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.