ZWE23ESNCSS General Electric Refrigerator - Instructions

Repair man thought it was the control board and an issue with a relay on the board. Purchased the new board but found out the board was fine, and it was the recirculating fan that would go out intermediately.

Tried ordering that part from Part Select since they have been great, but GE discontinued the part and their was not a replacement available. After much research, found the new replacement part number and ordered that, it went in quickly and for now seems to have solved the problem.

Literally turned off the water to the refrigerator, disconnected the lines from the back and took one screw loose from the inside of the unit. Slid out old filter connection and slid in the new one and did reverse process.

Move the refrigerator away from the wall.
Disconnect the refrigerator.
Remove bottom drawer.
Remove two criisper drawers.
Remove crisper drawer slides, one bolt near the front of each slide.
Push slides off pin at back.
Remove bottom panel at the back of the refrigerator to access fan.
Remove fan, held with a couple of screws.
Remove rubber gasket from around old fan and put the gasket around new fan.
install new fan and bolt in place.
Replace lower panel at back at back of refrigerator.
Reinstall drawer slides, hook at back and bold at front
Reinstall drawers.
Reconnect refrigerator power.
Push refrigerator back in place and adjust feed to hold in place.

Received the wrong spring. It is larger in diameter and the legs are too long. I used pliers to modify the spring for a temporary fix. Emailed CS about the wrong part and have never received any response back?

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

After looking up what might be the problem, I ordered a new control
board. It was extremely easy to replace. Unfortunately it was not operational. I had to replace my refrigerator. The return process was very easy and my refund was processed quickly.

Remove all trays, no need to turn app. off,
remove cover on top of back panel, may be a little difficult
remove 2 screws , one behind top plate, one in the middle of large back cover.
remove small cover located at the bottom of the back cover discinnect electrical plug,
remove or loosen 6 screws on lower evap cover, there is no need to remove evap cover, just pry it loose from back.
lift back cover off and disconnect electrical fan will be at the bottom of the large cover.
run warm water over fan and push out.
remove rubber cover and install on new fan,
reinstall new fan and reverse process.
very easy and simple and only takes about 30 minutes.

The glass fits easily under a plastic ridge that is the frame holding the 2 vegetable drawers below. Slide the back side of the glass under the ridge, and then gently place the front of the glass in the groove where it goes on top of the vegetable drawers.
Its Super simple, and takes literally 30 seconds to complete.

Used ratchet set, and unscrewed old one and screwed in new. Disconnected the wires and plugged in new one.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new