ZISB360DNBII General Electric Refrigerator - Instructions

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

had to remove ice maker and several panels to get to the fan. wires for fan encapsulated so had to cut old and new wires then solder them together while working inside the small freezer area. not too bad all in all took about an hour to get it done. no more wind thru the trees noise and is working fine

1) remove the ice bucket. 2) remove light cover and bulb. 3) remove back panel with 2 screws. 4) remove fan shield. 5) unlug 2 elec connections. 6) remove fan housing. 7) extract wiring grommet and use exacto knife to slice thru grommet along the length of it to release wires. don't cut light wires. 8) cut up old fan/light electrical plug to free wire nubs for light. 9) install nubs in new fan plug. 10) remove old fan motor, pull blades. 11) install blades on new fan moter and install fan into housing. 11) reinstall

Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.

The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

My refrigerator was making a high pitched kind of howling noise. The PartSelect symptom that was closest was “unusual noise” and when I clicked that it said the evaporator fan motor fixes the symptom 32% of the time. Since my freezer fan speed sounded like it was constantly changing I went ahead and bought one which PartSelect delivered promptly. The installation video was great and although my freezer was not identical to the one in the video, the video was still very helpful. The only thing it didn’t say was how to tell if my freezer motor was the one with the thermistor although I suspect that they all are and that PartSelect is simply trying to save us money by showing us how to splice in a motor without a thermistor. Anyway, since I would have had to disassemble the freezer before buying the part to find out for sure, I just bought the one without the thermistor. This just meant I had to splice the new motor in, just like in the video. I think I would have preferred buying the motor with the thermistor even though it was more expensive. In the end my problem is solved so I’m happy. This is the third time that I’ve had to repair this GE refrigerator and PartSelect has been a valuable resource each time.

followed you online video and it was easy and simple repair only took about an hour frig is back quiet and working fine thanks also parts come fast

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

i followed a video that was on your site, the video couldn't have been easier to follow it was step by step and very easy to follow, i replaced the evaporator fan motor and everything is working fine, i did notice that the evaporator coil was frozen pretty bad when i removed the back freezer panel i am going to check it again in a couple of weeks to make sure i don't have a defrosting problem as of now everything is fine i am hoping it was just the bad fan motor causing the coil to freeze up because of no air movement over the coil

Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved