GTS18FMLFES General Electric Refrigerator - Instructions

Watched video on website then removed old ice maker. New one went in without any problems. Working great. I am a 60 year old woman and had never done anything like this but so easy. Husband scared now, doesn't know what project I will take on next.

The instruction video was great, mine was easy than even the video showed it to be. I changed it out in less than 15 minutes and it works great. The niocve things I didn't have to wait for a repairman or my husband to fix the problem.

turn off water. turn off electricity. empty freezer section of frozen food. remove ice bucket. loosen two screws holding IM to wall of refrigerator. lift off icemaker, and then unplug it as you remove it. INSTALL new IM by: putting new water funnel onto new IM. attaching adapter cord to IM. plug in IM electrical cord to refrigerator and then hang the new IM onto the two loosened screws on the refrig wall. Now tighten the two screws. the extra adapter electrical cord hangs below the new IM, but does not get in the way when you reinstall old ice bucket. reload food, turn on elec and water. PS. i had a crack in the casing of the new IM, so i got a new one, but that one was cracked too. so i just installed the second cracked one. hope it is not a problem.

install icemaker water was allways delivered to previous unit water is not being delivered to icemaker still having difficulty

I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just barely. But I'm back in the ice again, no dripping water, all is good.

Installing the actual ice maker was quite easy. What takes most of the time is preparing the freezer for the install. Need to remove all shelving, (and the door) to gain access to the unit. The ice maker is simple to install once access is achieved. Putting everything back together takes some time.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

Condenser fan motor was running slow. This was not a problem included in your list of possible problems. I thought that maybe the capacitor was bad but have no way to check it. So I ordered one. when I received it, I installed it. That was not the problem. So I ordered a fan motor and installed it. That was not the problem. So finally I ordered a control board and installed it. That solved the problem. So maybe you should put "cond.fan motor runs slow" in your list of possible faults and what causes that problem. Capacitor was easy to install, simply remove the cover plate, flip off retaining wire, unplug the capacitor and replace. Fan motor was a bit more difficult. It must be removed from mount after fan scroll is removed. Remove one screw that holds scroll, bend the top down and remove. Then pull hard on fan blade to remove it. It must be installed on new motor. Two screws in frame mount can be removed with some effort if you have a 1/4" drive ratchet with a Phillips screwdriver bit. Then pull frame open and install new motor. Push fan blade on new motor shaft hard. Replacing control board was easy. I used a pair of long nose pliers with 90 degree bend to get mounting pins closed to pull board off.

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....

i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess

Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.

Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen