GTE17GSNDRSS General Electric Refrigerator - Instructions

The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!

I followed the instructions in the video. The decorative parts were slightly different than in the video, such as screws at the top versus the bottom, but all of the working parts were the same. I was somewhat hesitant about applying pressure to remove the locking spring and fan blades and to replace them but the video reassured me and all went well. The refrigerator is operating as quietly as when it was brand new.

watch the video very good

I replaced the noisy evaporator fan motor after watching the video provided. All went well and now I have a much quieter refrigerator. I took apart the old evaporator motor to see why it rattled when moved and it had an electrical part that came undone and was the cause of the obnoxious noise that came from the refrigerator. Now, my wife and I can sleep better now that the noisy fan was replaced.

Removed all the freezer inside panels to inspect the motor before I ordered the part. It looked like a relatively easy job to change it. I also watched the really nice video on the website that re-inforced my confidence in doing the job. The part came in a few days. I disassembled the freezer interior exactly as the video showed.(Warning: be careful with the styrofoam piece if the fridge is not fully defrosted. The ice build-up could cause it to break when trying to pull it out!)The only problem I had was getting the little collar on and off the motor fan shaft, and getting the fan off the shaft. I had to pull really hard for it to come loose and then I had to push really hard to get it back on the new motor shaft. I didn't know if could have used any kind of lubricant or not, so I didn't. After that the re-assembly inside the freezer went well, being careful to put everything back in the correct order and position. Started the fridge back up and it has been running very quietly ever since. But, most important, my wife was impressed with my work and is very pleased with the result!

First I looked at the video on changing out the fan.Made a lot of difference. Everything was covered and made it simple. Wish I had gotten two grommets but the back one was in good shape and worked fine. My hearing isn't great but now I can't even hear the thing run unless the freezer door is open. The shipping was great! You sent it out immediately and in a few days it was here.

The light switch was accidentally broken. I looked it up on your site and found the part. I ordered it and switched it out in a matter of minutes. It also helped having people who purchased their switches from the site explain how they repaired their switches with relative ease.

Used a 2" putty knife to lift off the old switch. Disconnected the broken switch and replaced it with the new one. Took about 1 minute.

i followed all the other submited solutions. really easy. popped out the broken light switch with thin tip screwdriver. careful not to let wires slip into compartment. then attached wires as i pulled them off broken switch. then carefully pop the new switch back in the slot. when i was younger i worked for an appliance repair company. i felt confident in this repair.

I first watched the video on how to do it via YouTube, to make sure there were no hidden surprises. This was probably the easiest/ quickest repair I have ever done, the ONLY thing that took any time was removing the food from the freezer

Used screw driver to lightly remove the old switch. Disconnected the 2 electrical leads to the old switch, then I connected those leads to the new switch. The light immediately came back on and I placed the switch into its housing hole and popped it in place. It works perfectly now. My wife said "let there be light"! Very easy installation. Thanks.

frig ran to much and pump on to long noticed light switch sticking when door was opened replaced the light switch took care of the problem the switch controlles more than just the light popped out with a screwdriver careful to find the side of it that has the retainer clip on it and the direction of the switch in correct position so it goes off when you close the door flat side facing the back a 2 minute job at most

Replaced light switch. Defrost cycle remains suspect but refrigerator has worked OK for about 10 days.

Things fall out of my refrigerator frequently thus the broken lite switch. Thought tape would solve until new part arrived. Thank goodness part came the next day as even with tape on and door close and light bulbs removed fridge read door as open and would not cool It is programmed not to run with door open. Within 24 hours part was delivered, unbelievable . It was that fast. Easy insertion and plugged in to the wiring and my refridge once more recognized the door was shut and began cooling. Thanks again

Part came in a couple of days, very fast delivery. Read how other people installed. Only drawback was the youtube video was not available. Thanks again!