GTE16DTNDRCC General Electric Refrigerator - Instructions

I did folllow the instructions on the video step by step.

common sense,removed plate,removed mounting bracked,unplugged,reversed order,and that was it.

I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The fridge works as good as new. Thanks a ton!

It has been my experience that these motors sometimes die when the refrigerator is overfilled and motor strains to keep refrigerator cold. And this motor is used in several models of refrigerators. That said, sometimes the hook-up is slightly different between other units. The available video is good, but like I said, circumstances will be slightly different between various models.

After cleaning out freezer (plug disconnected first), start to remove outer plastic covers. If you want to keep track of the different steps, you can take pictures with your cellphone. And if there are any connecting wire attachments you think you might not remember, again, you can take a picture, or label with tape (colored tape, or by writing on the tape). And for keeping track of the different-size screws, I place them in a muffin tin, keeping an order of left to right and top to bottom in the tin. When removing Styrofoam blocks in bottom center, make sure you remove any remaining ice underneath in the hole so refrigerator can "breathe". Freezer air is moved below to refrigerator compartment, so a blocked vent hole will strain refrigerator as it tries to maintain its temperature setting and can be the cause of your failed motor.

After replacing motor onto bracket with grommets and blade, don't completely tighten. Position plastic cover with hole opening over motor and blade assembly. Twirl motor blade to see if there is any interference with cover. If not, take away cover and tighten motor on bracket. If there is any rubbing, adjust motor/blade assembly accordingly before tightening in place. Putting everything back together is in reverse order.

Installation was super easy. I just removed first both drawers and then the base where the glass was installed, placed the new glass there carefully making sure that it fitted inside the gap to secure it and place everything back to the fridge the way it was. Presto!

Despite attempts to quiet the 2 year old fan, I went ahead and replaced it. Part Select was prompt with a new one at my door less than 24 hours. It was just the fan motor, so took a couple extra steps to place it in the metal housing, but no problems and though the frig still makes noises, it's not coming from the fan as before.

Followed the instructions on the repair video and it made very easy. Also saved us a lot of money. Thanks for your help.

Took back out of freezer compartment, pulled plug and removed old motor, inserted new parts. It was
easy and the parts arrived the day after I ordered
online, even though I chose the cheapest shipping
option. Nothing in my freezer had a chance to thaw
out.

First I removed the two screws, the fan and unpluged the electrical connection. Then, plugged in the new part and then screw it back together.

gasket is pressed fit into a groove on the refrigerator door replacement only takes 5-10 minutes.

Took out old put new in. Watched a u tube, no problems

I FOLLOWED YOUR VIDEO............WAS EASY. THANKS

On the move-in cleaning of the refrigerator I accidentally broke the glass encased shelf, and I don't believe there was a cover (glass or otherwise) in place that covered the Fresh Fruit and Vegetable bins. Wondering through the internet I found Part Select, ordered Parts 224 and 228. Installation really did take less than 30 minutes including, washing, drying, and placement of the two shelves. It's exactly what was needed. The refrigerator once again looks like a refrigerator with all the shelves in place. The customer service folks were more than helpful. All you need to do before placing the order is look at what you need to replace, write down the the model number, the serial number of your product part needed and chat with the customer service folks. All should go well. I'm happy.

Want to thank Haley, and Steve in Parts Select, for assisting me in replacing the GE freezer gasket, which was a very EASY process, took all of two minutes! The video did help.

removed cover over fan, four screws. removed two screws ,that holds fan in place,removed two more screws that holds fan in bracket,then reinstalled