DTS18ICOVERRBB General Electric Refrigerator - Instructions

removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

Bing , Bang, Boom.

Unplug. Remove back cover. Remove retainer (simple wire clip) from overload. Unplug overload from compressor. Remove two power wires (if stabs are tight you might need pliers). Note which wire goes where. Remove capacitor from overload (just pul it straight out .. Pull hard or pry a little with screwdriver. Insert capacitor into new switch. Reattach wires to same place in switch. Insert switch into compressor. Replace retainer clip. Replace rear cover with original screws. Plug in. Cool!

Removed two screws holding the cover. Unclipped and unplugged the defroster timer. Plugged in the new one . Replaced the cover. Finished.

I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into position my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer
Certainly not PartSelect's fault. They have great service.

Removed shelf by pushing to left and lifting up on RH end. Removed screws in plastic cooling tower and slid tower up. Pulled back wall of freezer compartment out, RH side first. Removed two screws from fan bracket, unplugged fan wiring harness by compressing connector spring clips and pulling joint apart. Pulled fan blade off (note location of blade on shaft for reinstall alignment purposes), removed both green grommets.Then just reinstalled new items.My philosphy on repairs of this nature is to replace all related parts that could be contributing to problem. The parts are cheap compared to the aggravation and inconvenience of doing the repair several times until you fix the problem. You don't need to purchase the compression ring if you buy the fan blade as it has one already installed on it. Problem solved, though now that the noise is gone am hearing fainter similar noises from lower fan. Should I be surprised, both fans are of similar design.

Removed the ice maker from the freezer. Removed the switch. Tested the switch with a multimeter. Ordered a new switch. Replaced it in the box. Installed the ice maker ( 3screws and electric cord plug. It works. Details available on the internet.

The part i received fit perfect, i just removed the old part and put the new part in with the screw driver.Really easy

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

We have an older model refrigerator and thought it would be impossible to find a replacement ice bucket for the freezer. Not only did you have the exact part but it came unbelieveably fast. I would use your website again!

Was concerned that new icemaker was quite a bit different than the one we were replacing. Called GE to confirm it was correct.

Went ahead and installed the unit, using the supplied electric cable adapter.

A little difficult to deal with the extra cable, but everything worked OK and it's making ice normally.