TFX22PMC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from Randallstown, MD
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
the auger was rusty, causing ice to have brown spots
Pay close attention to how you disassemble everything. You might even want to take a picture. I taped all the screws right where I unscrewed them, to make sure they were replaced in the right section. Also use the picture diagram that on the computer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Naples, FL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Fridge door was not self-closing
Followed step-by-step instructions in previous post. Note that there are TWO approaches, both of which work.
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from New York, NY
- Parts Used:
- WR17X1407
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The light shield covering the bulb in the freezer cracked.
This was an extremely easy repair. The old light shield snapped out and the new one snapped in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phyllis from owensville, MO
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old Cam Had Deteriorated, And Was Breaking Into Pieces And Falling Off.
We taped the door with 3 pieces of duct tape, then put boards under it. Used socket set to remove cam and then cut off rivet so we could just use a screw to keep in place. . . Just for your information, I ordered 2 cams, and was glad I did as I need 2 to make the repair. . . Didn't read about this online or on order recommendation. The cams go 1 up and 1 down thanks for the installation repair stories, it inspired us to "do it ourselves " and we saved about $75 to $100. 00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Azle, TX
- Parts Used:
- WR17X2740
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
The auger was rusted with age and made the ice taste bad.
The disassembly and reassembly was straightforward but the parts diagram was very helpful to help you get it back together. Make sure you get the convexity of the clip that retains the clear plastic barrel to the auger pointing in the right direction. The metal plate that that comes out with the assembly seems to rust as fast as the auger, so you should just order that when you order the auger. I did not replace the plate so I cleaned it and painted it with epoxy paint before I reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Spring, TX
- Parts Used:
- WR62X23154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jimmy from saluda, SC
- Parts Used:
- WR17X2740
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
would not dispence ice
remove ice bucket and replace broken augar
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Windham, NH
- Parts Used:
- WR17X2760
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
rust in the ice
there was rust inbedded in the ice cube. replaced the front plate in the ice maker bin. If you can't remember what parts you remover, take pictures of the replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Yakima, WA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
door was not closing properly
watched the video on changing the cam and then did the repair as per the instructions. the job was easy and now the door works as it should. that saved me lots of money by doing it myself. thanks, Martin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Wheaton, IL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door didn't shut cleaning, by itself
I watched the video online, and said, "hey, I can do that." And yep, I did. I'm pretty comfortable with handyman work - but had never tackled a frig door before. The door closing cam that had completely come apart turned out to be straight forward to fix with the replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Chevy Chase, MD
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator door didn't close without a big push.
Took door off. Replaced two cams at bottom of door, referencing those on the bottom of the freezer door. Also followed a video on the net. Worked like a jewel!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Corpus Christi, TX
- Parts Used:
- WR49X10183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rust in ice
Replaced auger and front helix kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Anaheim, CA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
broken cam riser on the bottom of the door
I ordered a cam riser for the refrigerator door. I watched the "how to" video the day I ordered the part. It took about a week to get the part, but I was ready when it arrived. The 'how to' video was a big help. It showed me how to take off the door and replace the part. The process was quite simple! Oh! Don't forget to turn the refrigerator on again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol J from Alexandria, KY
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Door would not close properly at the last few inches, now it closes good at this time but now need to be raised up to the 5/8 inch as the book says, haven't done that yet
the door closing cam works fine.
Was this instruction helpful to you?
Thank you for voting!