Models > TFK25PRDAWW > Instructions

TFK25PRDAWW General Electric Refrigerator - Instructions

Jump to:

All Instructions for the TFK25PRDAWW
76 - 90 of 451
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Kyoko from Bellevue, WA
Parts Used:
WR17X11653
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
frost/ice buildup in icemaker chute in the freezer door
The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Lake Quivira, KS
Parts Used:
WR71X10196
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Plastic Left Ice Bucket Shelf (slide) at the back broke around the pop rivet into the shelf .
At the front of the shelf there is a Phillips metal sheet metal screw that holds the front of the shelf in place. Its removal was fairly set straight forward but removing the pop rivet was awkward and took some time to drill out from the rear metal shelf. Once the rivet was out, it was easy finding a small screw that would hold the shelf in place since I didn't have any pop rivets that would fit sufficiently tight or long enough.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Travis from Hillsboro, OR
Parts Used:
WR17X3489
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light Shield Broke Off
The light shield is only held in with a single screw, so it was the simplest install ever - unscrew the old light shield (in my case, the remaining piece of the light shield), put the new shield in place, and screw it down. Doesn't get any easier than that.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ralph from Indianapolis, IN
Parts Used:
WR17X4153
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Grill was tarnished and flaking.
Grill for the water dispenser in the door. All I had to do was drop the new one in place.

Received the new grill in one day after ordering.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fred from Union, NJ
Parts Used:
WR17X3489
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The freezer light shield was broken.
I removed the ice maker,removed the broken piece of the old light shield,screwed the new light shield in place,and replaced the ice maker.It took all of 5 minutes.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from Colleyville, TX
Parts Used:
WR17X11653
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
No water through door dispenser
Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Maxine from Glen St. Mary, FL
Parts Used:
WR12X10152, WR12X10123, WR12X10782
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Handles Turned A Ugly Yellow
I just popped the upper and lower tail handle off, unscrewed the door handle, then I screwed in the new door handle and popped the upper and lower tail handle back on. Easy as pie because I was concerned since I am a female.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Wyckoff, NJ
Parts Used:
WR30X10093
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Ice maker stopped making ice
I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Anaheim, CA
Parts Used:
WR30X10093
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
The icemaker quit making ice and the water started forming on the bottom of the ice bucket.
First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from HAYMARKET, VA
Parts Used:
WR17X11653
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Flapper was worn and misshapen allowing warm air in freezer, ice cubes to melt and drip and impairing function of ice dispenser. Frost formed in ice dispensing chute also.
Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip M. from SIMPSONVILLE, SC
Parts Used:
WR32X1461
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
GE vegetable drawer broken.
Concerned about removing and attaching front panel to broken drawer. Rep. said wasn't sure but most just snapped together. Rep. was correct. No tools required.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George V. from PITTSBURGH, PA
Parts Used:
WR17X3489
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Freezer Light Shield Cracked at mid fastening point
replaced the broken one with the new part
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruno from ROME, NY
Parts Used:
WR12X10152, WR12X10123
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Old and yellow handles
Just take out the old ones, and clip in the new ones
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from BRICK, NJ
Parts Used:
WR17X11653
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
I just followed the instructions on the video and it was exactly as they said......no surprises.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
M R from Las Vegas, NV
Parts Used:
WR71X10197, WR71X10196, WR30X256
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Ice maker bump and grind
The ice bucket supports had split, and broken away from the refrigerator wall causing the ice dispenser bucket to sag, and bump and grind. The b&g wore away the ice screw support at the rear of the bucket, causing intermittent ice dispensing. The ice bucket was removed to allow access to the ice bucket supports. The supports were attached to the refrigerator by two screws. One along the front side, the other at the rear attached to a protruding tang. One of these broken off, the other was stuck, and had to be forced off its mount. The rear mount was expanded by drilling a slightly larger hole to accommodate a nut and bolt assembly. The new support units were re-attached to the refrigerator front and back using screws and the nut and bolt in the appropriate places. The ice bucket installation was a tad more difficult. The hardware from the original bucket was removed and installed on the replacement bucket. This proved to be a bit tricky remembering the exact location of the parts, and coordinating the screw mechanism with the driver mechanism. The ice fill starter switch is a bit unusual in that it has to go into a slot that is not visible when inserting the ice dispenser bucket into the ice maker compartment. You have to finagle the bucket into place and get all the parts in the correct slots. It was a piece of cake for the average husband.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TFK25PRDAWW
76 - 90 of 451