CFE28USHNSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from LONDONDERRY, NH
- Parts Used:
- WR60X26866
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
temp almost 60 in refrigerator compartment, but 31 in bottom drawer where meat stored.
Watch this very good refrigerator evaporator fan replacement video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BLUE RIDGE, GA
- Parts Used:
- WR02X13684
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken water filter appliance
Literally turned off the water to the refrigerator, disconnected the lines from the back and took one screw loose from the inside of the unit. Slid out old filter connection and slid in the new one and did reverse process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from ROSETO, PA
- Parts Used:
- WR55X24064
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer not getting cold enough to freeze ice cream
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from EDMONDS, WA
- Parts Used:
- RPWFE
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace old filter with new water filter.
Remove old filter by pulling and not twisting and insert new filter by pushing in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from LA PINE, OR
- Parts Used:
- WR01X11052
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Broken spring on bottom hinge of left door mullion.
Received the wrong spring. It is larger in diameter and the legs are too long. I used pliers to modify the spring for a temporary fix. Emailed CS about the wrong part and have never received any response back?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alison from WOLCOTT, CT
- Parts Used:
- WR32X10865
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace glass shelf in fridge
It was super easy! The glass came packaged and safe. Once I unwrapped it, I slid it in the firdge and it just popped into place. So super easy. And now we know for next time when taking it out to clean, (the reason it shattered in the first place) you should let the glass get to room tempurature before cleaning it with water or it will shatter! OOPS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from LAKELAND, FL
- Parts Used:
- RPWFE
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace water filter in icemaker
This was the first time I took out the old filter on my new refrigerator and added the new one. It was a little hard getting the old one out because I was afraid to pull on it but it did come out ok and was easy to put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from SILVER SPRING, MD
- Parts Used:
- WR32X10865
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper Pan Glass accidentally dropped and crashed!!!
Search online and came across PARTSELECT website!!! this is amazing when I opened the website and see a labeled drawing, so I know what part number to order, it arrived on time and when I install it fits very well, one lesson I've learned is whenever you removed this glass in the chiller box you have to reinstall the glass properly by inserting one of the side to the insert slide of the chiller so it will not move! I'M VERY HAPPY!!!! THANKS!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colin from BREWSTER, MA
- Parts Used:
- WR55X45230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Touch screen display would not respond
Unplug refrigerator or turn off circuit breaker.
Insert knife blade or other thin blade into joint at bottom of screen bezel (where there is a color change) and pry up slightly until top of bezel pops out. Probably need to do this in several places until the entire top edge is out slightly. Pull the top of bezel out slightly and lift up to remove.
Remove 4 1/4" hex head screws to loosen control panel. Pull control panel out from door and remove three wiring connectors. You can now completely remove panel from refrigerator door.
Use T15 Torx driver to remove 5 screws on main circuit board and 2 on the small attached board. Remove and save plastic insulator piece.
Install new boards and insulator piece using the Torx screws. Reconnect the three wiring connectors and remount the control panel using the hex head screws.
Reinstall the screen bezel by sliding the bottom in first. Align the tabs on the bezel with the mating slots in the lower panel. When bezel is all the way down push in the top edge to engage the retainer clips.
Plug in refrigerator or turn on circuit breaker. Control should now go through the startup sequence.
Insert knife blade or other thin blade into joint at bottom of screen bezel (where there is a color change) and pry up slightly until top of bezel pops out. Probably need to do this in several places until the entire top edge is out slightly. Pull the top of bezel out slightly and lift up to remove.
Remove 4 1/4" hex head screws to loosen control panel. Pull control panel out from door and remove three wiring connectors. You can now completely remove panel from refrigerator door.
Use T15 Torx driver to remove 5 screws on main circuit board and 2 on the small attached board. Remove and save plastic insulator piece.
Install new boards and insulator piece using the Torx screws. Reconnect the three wiring connectors and remount the control panel using the hex head screws.
Reinstall the screen bezel by sliding the bottom in first. Align the tabs on the bezel with the mating slots in the lower panel. When bezel is all the way down push in the top edge to engage the retainer clips.
Plug in refrigerator or turn on circuit breaker. Control should now go through the startup sequence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from PITTSBURG, CA
- Parts Used:
- WR55X24064
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator to warm
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from ST AUGUSTINE, FL
- Parts Used:
- WR11X10031
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch for ice box door broke off
Received replacement part. There is a cover over the ice box latch. Pried it off with a screwdriver head. Took the broken latch off replaced new latch to cover and replaced on the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WEST END, NC
- Parts Used:
- WR32X10865
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
We broke the glass shelf above the vegetable bins, when we took it out to clean it.
I went on line, found PartSelect, located the diagram for our model, selected the part and ordered it. The part arrived in about 5 days, well packaged. We removed it from the packaging, and installed the new shelf. Extremely easy process. The exploded diagram on the web site allowed me to make sure I was ordering the right part.
Excellent process!
Excellent process!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheryl from SAINT LOUIS, MO
- Parts Used:
- RPWFE
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
I lack physical strength
I asked two strong male neighbors to do the work and told them how to do it. Follow the simple directions on the box. You can Google it, but it will tell you the same directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LA PLATA, MD
- Parts Used:
- WR60X26866
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
fan noise
followed install on line
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from LAKE ELMO, MN
- Parts Used:
- WR57X27487
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water trickling out of refrigerator water dispenser.
1. Verified good water flow by unplugging incoming water and makIng sure there was good pressure.
2. Re-attached water supply line and unplugged water line after the electronic valve to test water pressure from valve when hitting the dispense button in the front of the refrigerator.
Found very little flow directly after the valve.
Replaced valve and now everything is good. (Refrigerator is less than 2 years old)
2. Re-attached water supply line and unplugged water line after the electronic valve to test water pressure from valve when hitting the dispense button in the front of the refrigerator.
Found very little flow directly after the valve.
Replaced valve and now everything is good. (Refrigerator is less than 2 years old)
Was this instruction helpful to you?
Thank you for voting!