PWE23KELBDS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from LONDONDERRY, NH
- Parts Used:
- WR60X26866
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
temp almost 60 in refrigerator compartment, but 31 in bottom drawer where meat stored.
Watch this very good refrigerator evaporator fan replacement video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BLUE RIDGE, GA
- Parts Used:
- WR02X13684
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken water filter appliance
Literally turned off the water to the refrigerator, disconnected the lines from the back and took one screw loose from the inside of the unit. Slid out old filter connection and slid in the new one and did reverse process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from ROSETO, PA
- Parts Used:
- WR55X24064
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer not getting cold enough to freeze ice cream
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from EDMONDS, WA
- Parts Used:
- RPWFE
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replace old filter with new water filter.
Remove old filter by pulling and not twisting and insert new filter by pushing in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from LA PINE, OR
- Parts Used:
- WR01X11052
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Broken spring on bottom hinge of left door mullion.
Received the wrong spring. It is larger in diameter and the legs are too long. I used pliers to modify the spring for a temporary fix. Emailed CS about the wrong part and have never received any response back?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from LAKELAND, FL
- Parts Used:
- RPWFE
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace water filter in icemaker
This was the first time I took out the old filter on my new refrigerator and added the new one. It was a little hard getting the old one out because I was afraid to pull on it but it did come out ok and was easy to put the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from PITTSBURG, CA
- Parts Used:
- WR55X24064
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator to warm
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from LA PLATA, MD
- Parts Used:
- WR60X26866
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
fan noise
followed install on line
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheryl from SAINT LOUIS, MO
- Parts Used:
- RPWFE
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
I lack physical strength
I asked two strong male neighbors to do the work and told them how to do it. Follow the simple directions on the box. You can Google it, but it will tell you the same directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from YORBA LINDA, CA
- Parts Used:
- WR32X10911
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
While cleaning, I Broke the glass that tops the 2 vegetable drawers.
The glass fits easily under a plastic ridge that is the frame holding the 2 vegetable drawers below. Slide the back side of the glass under the ridge, and then gently place the front of the glass in the groove where it goes on top of the vegetable drawers.
Its Super simple, and takes literally 30 seconds to complete.
Its Super simple, and takes literally 30 seconds to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from DIAMOND BAR, CA
- Parts Used:
- WR17X13240
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mullion not working. Replaced mullion.
1. Turned power off.
2. Removed 2 screws holding plastid plate which connected electrical wire from mullion to door (requires Torq-tip screwdriver).
3. Unplugged wire plug behind the plate.
4. Lifted up old mullion from 2 slots holding it in place to remove it from door.
5. Inserted new mullion into slots on door.
6. Connected electrical wire to plug inside door.
7. Screwed 2 screws to reattached plastic plate to door.
8. Turned power back on.
2. Removed 2 screws holding plastid plate which connected electrical wire from mullion to door (requires Torq-tip screwdriver).
3. Unplugged wire plug behind the plate.
4. Lifted up old mullion from 2 slots holding it in place to remove it from door.
5. Inserted new mullion into slots on door.
6. Connected electrical wire to plug inside door.
7. Screwed 2 screws to reattached plastic plate to door.
8. Turned power back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Finleyville, PA
- Parts Used:
- WR55X46805
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
After power outage, my refrigerator would not cool after power came back.
After looking up what might be the problem, I ordered a new control
board. It was extremely easy to replace. Unfortunately it was not operational. I had to replace my refrigerator. The return process was very easy and my refund was processed quickly.
board. It was extremely easy to replace. Unfortunately it was not operational. I had to replace my refrigerator. The return process was very easy and my refund was processed quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from GULF SHORES, AL
- Parts Used:
- WR08X22874
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace starter relay switch
I followed u-tube instructions.
Took off the old switch and put the new one on.
Took off the old switch and put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from STATEN ISLAND, NY
- Parts Used:
- WR30X28682
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Malfunctioning ice maker
Used ratchet set, and unscrewed old one and screwed in new. Disconnected the wires and plugged in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ATHENS, AL
- Parts Used:
- WR60X26866
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Insufficient cooling upper food storage area
Pulled out bottom crisper drawers. Removed drawer slides. Removed side plastic panels, then removed back panel which exposed the fan. Removed fan and replaced with new fan. Had to use the heat gun because there was ice buildup on left corner of rear panel. Reassembled in reverse order. There is several excellent videos on You Tube.
Was this instruction helpful to you?
Thank you for voting!