PFD28KELBDS General Electric Refrigerator - Instructions

I determined one of the five LED lights in the refrigerator was dead by swapping it with a working one. The refrigerator lights are wired in series and if one of the lights is dead the remaining ones turn on, but very dim. I called PartSelect.com and thanks to their help we determined the correct part to order which is the oval-shaped cover LED assembly which includes the cover, LED, and female connector. The part from PartSelect arrived in three days. The oval-shape LED plastic Cover assembly is mounted on the refrigerator and held by a couple of side latches. First unplug the refrigerator and then proceed to lightly pry the oval-shaped cover side facing the rear of the refrigerator with your finger nail to remove it. With the LED cover removed you can then press on the LED connector tab to slide it off. Now slide the female connector of the replacement part to the refrigerator male connector and snap the oval-shape plastic cover onto the refrigerator receptacle and then plug it back to its outlet. Now all the lights in the refrigerator should light up brightly! That's all folks. Hope this helps. Good luck. Yours truly.

It snapped in place.

I ended up ordering two valves, both of which were defective (bad) and would not pass water, for a total of $116.66. Then I had to get a service tech to install yet another valve (also a GE part) that was good and that fixed the problem (for another $187.00 charge). These parts seem to come from Canada or beyond so be careful if you order them as they too may be bad. I finally received a refund for one but I'm still hunting for a USA address to return the other one I need a refund for...good luck.

I diagnosed the sensors in my refrigerator by holding the sensor in and seeing if I could trick the sensor it partially worked. I then used a multimeter and did an ohm test on both sensors multiple times open and closed the switch to verify which switch failed because it worked a couple times but not always. It ended up being the switch on the left hand door with 3 terminals on it and after the replacement it has worked great for weeks now no issue. best 15 dollars and 25 minutes spent!

I didn’t open the part till I verified it was the same. Then I detached the assembly from the fridge and swapped the water lines individually. The metal bracket had gotten bent a little in shipment, but straightened easily and all went back together.

Installing the part repaired the fridge and freezer immediately.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

I recieved the package with the correct part number but the wrong part inside. The item in the package does not even resemble the part on the GE parts website. Tried to contact parts select but no luck.

Locate the light that is completely out, remove the assembly. Unplug the wire harness in the back. Plug in the new assembly and snap into place in the cabinet.

Popped it up and popped new one on

Ordered a new handle and replaced the old broken one.

Replaced Temperature Sensor and now it is getting cold.

It was very simple. Removed 4 screws on top of door where panel is located. Unplug 3 three connectors and removed board. reinstalled new one in reverse mode. On the down side this did not solve the problem. I am still working on it.

Removed old unit, remove plastic tape on new draw and washed the unit, inserted new draw. This is really an easy fix, no tools needed.

I looked online and it said GE does not make the support for my model Refrigerator/freezer. I looked the picture for this part and it looked like the same one so I bought it (very inexpensive) and an extra one just in case.
I took out most of the items on that sliding shelf and pulled it out. Found the correct socket for the nut and removed the remaining piece. Then just used the same nuts and new Glide support, tightened it up (but not too much, and tried the shelf.
It worked !!! I added the frozen foods and I was done. It was very fast. And by the way, I am not a big home repair person. EASY.