DFE28JMKKES General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kevin from FLORENCE, KY
- Parts Used:
- WR23X29161
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Wate Dispenser Not Working
Safety first, unplug fridge. Had to remove the top access panel, which consisted of 5 screws. Got access to the door switches. These are removed from the panel by depressing the plunger on the switch and sliding them out of the retainer. Transferred the wires over to the new switches one for one. Re-assembled. Dispenser works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from NORTHRIDGE, CA
- Parts Used:
- WR12X23646
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Freezer door handle broke off from constant pulling breaking the freezer air seal.
I attached the new handle and tightened the set screws with an Allen wrench. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E Lawrence from PINECREST, FL
- Parts Used:
- WR30X28731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker was dropping black particles that looked like dirt or mold. What they were was the corrosion of the metallic (pot metal or aluminum) ice form and small corroded particles falling on the ice. The ice form looked like it was coated with teflon or a paint. this form needs to be metal so heati
Replaced the 8 year old icemaker.
Turned off power.
Did not need to turnoff water supply.
Removed the 1/4" hex head screw from the wire connector cover.
Removed the wire cover taking care to be careful with the thermister
temperature sensor which slides into a square channel in the cover.
Disconnected both wire connectors.
Unscrewed the 5/16" hex screw at bottom of icemaker to unmount the old icemaker, lift the icemaker up 1/2" and out and discard.
Installed new icemaker in reverse order.
Turned off power.
Did not need to turnoff water supply.
Removed the 1/4" hex head screw from the wire connector cover.
Removed the wire cover taking care to be careful with the thermister
temperature sensor which slides into a square channel in the cover.
Disconnected both wire connectors.
Unscrewed the 5/16" hex screw at bottom of icemaker to unmount the old icemaker, lift the icemaker up 1/2" and out and discard.
Installed new icemaker in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from DIAMOND BAR, CA
- Parts Used:
- WR17X13240
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Mullion not working. Replaced mullion.
1. Turned power off.
2. Removed 2 screws holding plastid plate which connected electrical wire from mullion to door (requires Torq-tip screwdriver).
3. Unplugged wire plug behind the plate.
4. Lifted up old mullion from 2 slots holding it in place to remove it from door.
5. Inserted new mullion into slots on door.
6. Connected electrical wire to plug inside door.
7. Screwed 2 screws to reattached plastic plate to door.
8. Turned power back on.
2. Removed 2 screws holding plastid plate which connected electrical wire from mullion to door (requires Torq-tip screwdriver).
3. Unplugged wire plug behind the plate.
4. Lifted up old mullion from 2 slots holding it in place to remove it from door.
5. Inserted new mullion into slots on door.
6. Connected electrical wire to plug inside door.
7. Screwed 2 screws to reattached plastic plate to door.
8. Turned power back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LARRY from GEORGETOWN, TX
- Parts Used:
- WR60X35205
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
noise evap fan motor
Remove all trays, no need to turn app. off,
remove cover on top of back panel, may be a little difficult
remove 2 screws , one behind top plate, one in the middle of large back cover.
remove small cover located at the bottom of the back cover discinnect electrical plug,
remove or loosen 6 screws on lower evap cover, there is no need to remove evap cover, just pry it loose from back.
lift back cover off and disconnect electrical fan will be at the bottom of the large cover.
run warm water over fan and push out.
remove rubber cover and install on new fan,
reinstall new fan and reverse process.
very easy and simple and only takes about 30 minutes.
remove cover on top of back panel, may be a little difficult
remove 2 screws , one behind top plate, one in the middle of large back cover.
remove small cover located at the bottom of the back cover discinnect electrical plug,
remove or loosen 6 screws on lower evap cover, there is no need to remove evap cover, just pry it loose from back.
lift back cover off and disconnect electrical fan will be at the bottom of the large cover.
run warm water over fan and push out.
remove rubber cover and install on new fan,
reinstall new fan and reverse process.
very easy and simple and only takes about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from ROTONDA WEST, FL
- Parts Used:
- WR57X27527
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Very slow water flow despite filter change
I didn’t open the part till I verified it was the same. Then I detached the assembly from the fridge and swapped the water lines individually. The metal bracket had gotten bent a little in shipment, but straightened easily and all went back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from PIONEER, CA
- Parts Used:
- WR57X27487
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Low water flow from the dispenser.
Replaced the water solenoid that has a filter/screen as part of the unit.
Removed the back bottom plate. Turned off water supply, removed hose from water valve. Removed valve assembly, and un-pluged wiring. Installed new unit reverse of removal
Removed the back bottom plate. Turned off water supply, removed hose from water valve. Removed valve assembly, and un-pluged wiring. Installed new unit reverse of removal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerrit from ST AUGUSTINE, FL
- Parts Used:
- WR57X27527
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Water would not pass through the water valve solenoid to the rest of the fridge.
I ended up ordering two valves, both of which were defective (bad) and would not pass water, for a total of $116.66. Then I had to get a service tech to install yet another valve (also a GE part) that was good and that fixed the problem (for another $187.00 charge). These parts seem to come from Canada or beyond so be careful if you order them as they too may be bad. I finally received a refund for one but I'm still hunting for a USA address to return the other one I need a refund for...good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from ENDICOTT, NY
- Parts Used:
- WR55X24064
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
freezer stoped freezing
my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from VERO BEACH, FL
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The Refridgerator and Freezer were not cooling.
Installing the part repaired the fridge and freezer immediately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from BYRON, MN
- Parts Used:
- WR23X29161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
My light always stayed on and the icemaker stopped working.
I diagnosed the sensors in my refrigerator by holding the sensor in and seeing if I could trick the sensor it partially worked. I then used a multimeter and did an ohm test on both sensors multiple times open and closed the switch to verify which switch failed because it worked a couple times but not always. It ended up being the switch on the left hand door with 3 terminals on it and after the replacement it has worked great for weeks now no issue. best 15 dollars and 25 minutes spent!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paypal_shipping_address from Ripon, CA
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light would no longer turn on
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Benton Harbor, MI
- Parts Used:
- WR23X10725
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light out
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from DURYEA, PA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
both freezer and refigerator were warm.
I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sumlorq from Cleveland, OH
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch freezer door
put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil
Was this instruction helpful to you?
Thank you for voting!