XTS21FSKCSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from Abilene, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker was leaking water. Cubes were sticking inside tray.
Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pampa, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker was leaking
Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colby from Blanding, UT
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Starter/overload assembly and run capacitor were bad
Removed rer cover, unplugged starter assembly from side of compressor and replaced unit with a new one. Plugged fridge in and it works good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Broomfield, CO
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice make stopped making ice
Went to GE website and researched the problem for the model, determined that it was 90% sure it was the Ice maker, I ordered it and it arrived the next day, installed it and it began working immediately,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from decatur, GA
- Parts Used:
- WR55X24064
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Freezer And Frig Both Warm And Compressor Would Not Run
I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conti USA, Inc. from Fort Lauderdale, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
change of ice maker
It was exactly as shown in your instruction video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul J from Niceville, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker plastic piece had broken causing ice to not make properly and loose water to freeze things into chunks
I spent 15 - 20 minutes just hunting/deciding which of several sets of parts & directions to follow. The provided directions were not bad; but none of them quite matched my GE ADORA side-by-side model. Once I came up with the actions I would need to take...I was done in 5 minutes! The kit , as I said, came with all the parts one could need (and one or two un-needed parts included for other model GE refrigerators) I am very happy with PART SELECT...altough GE doesn't rate as high with me for their declining reliability.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from clinton, TN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
would not make ice
i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from Yorba linda, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was not making ice
Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Portland, ME
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cord
The adapter made the cord a bit long but other than that it was great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Edmond, OK
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Maker stopped making ice.
Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from JASPER, GA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was not making ice cubes
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grimes from Bartlett, TN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
ice maker very slow and arm that controls amount of ice sticking and quit making ice
took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Las Cruces, NM
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no ice
Followed the video, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from San Tan Valley, AZ
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice Maker stopped working
Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.
Was this instruction helpful to you?
Thank you for voting!