GFE24JBLJFTS General Electric Refrigerator - Instructions

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

no brainer took out the old put in the new! approximately 7 seconds total time.

Remove the screws from the two door pivot covers. Remove the covers and set aside. Remove the screws from the control board; disconnect the electrical connections; remove the door light switch, install door light switch then reinstall everything.

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

I ordered the 3 shelves from Parts Select requiring replacement based on the GNE25JGKFFWW Parts By Section diagram (parts 540, 541 & 542) and the removals and installations were very simple, no tools required but major issue was shelf 540 for left side of the refrigerator did not fit. Parts Select sent me the same wrong shelf 3 times and all were returned. Last conversation with Part Select rep they gave me the number to General Electric because they finally figured it out the the shelf (540) depicted on their website did not fit our refrigerator. I've purchased items from Parts Select before but sending the wrong part to us on 3 separate occasions was concerning

Pulled the fridge out. Removed the back panel over the mother board. Removed and replaced. Easy peasy and working well.

I Googled how to fix a ge door handle. It was super easy. Just slide it up, take it off and replace by putting the new one in place and sliding down till it clicks.

I couldn’t repair the problem because the part that came did not have the clips to crimp on the end that go into the modular connection,

Just placed the shelf on the door

Removed and replaced correct item received however one was cracked right out of undamaged properly packed box submitted claim and refund quickly processed by the seller recommend inspect upon receipt.

Repair was made simply and quickly by removing broken parts and replacing with new. No problems

followed part select video instructions

Unplugged unit and removed vented cover over compressor section. The run capacitor is a simple fix 1 Phillips head screw and 2 spade wire connectors. For the temperature sensor I had to remove all drawers and the ice maker to remove the back cover to expose the condenser. Put a bowl at the drain stem in the rear of the unit and used a heat gun to defrost the coils on the condenser. Cut the wire about 3" from the sensor end . cut about the same off the new sensor stripped the wires put shrink wrap on each wire, attached butt connecors . heat gun for the shrink wrap and reassembled everything. Simple job that took about a half hour to do both. I will monitor the fridge for a couple of weeks to see if I need to change the control board.

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

What an awesome site! After putting in my model number and finding the problem I was having, I simply picked the 2 parts that were most likely to solve the problem. I bought a defrost thermostat, and defrost heater. To a high certainty, they would solve my problem. They didn't however! I ended up having to buy a temperature sensor on another order a few weeks later when the problem resurfaced! My own fault. I should have bought it the first time. As others have written: the longest part of the job is defrosting the ice from the coil. One thing I did that I didn't see suggested: plug the drain hole below the coil. I put a couple towels in the bottom of the freezer and ran the hair dryer. Didn't take long. I read that the amount of water created will overflow the pan under the refrigerator, so I plugged the drain hole. Once you clean that mess up, the repair is pretty straight forward. Great site. Even through I had to make two separate purchases, I still saved a lot of money. Thanks!