GSA22KBMDFWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ken from THE VILLAGES, FL
- Parts Used:
- WR50X10068
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Frosting up in freezer ice freezing solid
Took out freezer rack took off the back panel also light bulb found the DEFROST THERMOSTAT cut the 2 wires remove the thermostat strip the wires on the new thermostat splice the to wires together with wire nut wrapped wire nuts with electrical tape put new thermostat back were the old came off of put panels back in place also the racks and bulb plunged in the power and guess what it works like a Champ with in 1 hour making ice and going through defrost cycle nice Thank You Guys for your video and the how to do Thanks Ken
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from TOMS RIVER, NJ
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Staying on defrost too long. Ice melting and as a result ice maker not working do to re-freeze
Per vidios
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from GREENSBORO, NC
- Parts Used:
- WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fan was not centered in the middle of the back panel opening.
Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from VALLEY CENTER, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Loud whirling noises when the motor started up, then they subside (and stop) in a short time
I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Allen, TX
- Parts Used:
- WR50X10068
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Fridge not cooling, freezer not defrosting
Must have spent 10+ hours solid looking up info on the internet. Our ice maker had broken years ago, the door flap had broken years ago and I thought this was the end of a fridge after just 6 years 8 months.
GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.
I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.
So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.
So now I'm back to order the ice maker part. The door flap will wait for another time.
Note: I've put in the time for novices and recognizing how the freezer is constructed.
Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.
Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!
GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.
I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.
So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.
So now I'm back to order the ice maker part. The door flap will wait for another time.
Note: I've put in the time for novices and recognizing how the freezer is constructed.
Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.
Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from GEORGETOWN, TX
- Parts Used:
- WR71X38317
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The existing dairy door came lose fell and brokeon tile floor.
The new part installed without problem always had great service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BAKERSFIELD, CA
- Parts Used:
- WR32X10834
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Bought a used refrigerator and it had a broken veggie drawer.
All I had to do was open the box, pull the drawer out, insert it in the fridge, and place the handle on and I was done. Thank you for making my fridge look new again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from OROVILLE, CA
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced broken dairy door
Took 2 seconds to replace door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from LTL EGG HBR, NJ
- Parts Used:
- WR32X10834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Veg/produce drawer cracked
Ordered replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from LAUREL, MD
- Parts Used:
- WR71X38317
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dairy door broken.
ordered a new one; took 1 second to put in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alcides from WINNETKA, CA
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Freezer was not defrosting. Ice accumulated inside of the back of freezer.
Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from WARRENTON, VA
- Parts Used:
- WR32X10835
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Meat pan wouldn't slide in or out - sides damaged
Slid new drawer in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GERARDO from rialto, CA
- Parts Used:
- WR55X10150
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Fan not working properly because temperature controldamage
Replace the temperature control and the fan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Liz from EDMONDS, WA
- Parts Used:
- WR32X10834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
veggie drawer was cracked and wouldn't slide in and out any longer
easy, we just placed the new vegetable drawer in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!