CFE28USHMSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jean from GULF SHORES, AL
- Parts Used:
- WR08X22874
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace starter relay switch
I followed u-tube instructions.
Took off the old switch and put the new one on.
Took off the old switch and put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from FLORENCE, KY
- Parts Used:
- WR23X29161
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Wate Dispenser Not Working
Safety first, unplug fridge. Had to remove the top access panel, which consisted of 5 screws. Got access to the door switches. These are removed from the panel by depressing the plunger on the switch and sliding them out of the retainer. Transferred the wires over to the new switches one for one. Re-assembled. Dispenser works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- E Lawrence from PINECREST, FL
- Parts Used:
- WR30X28731
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker was dropping black particles that looked like dirt or mold. What they were was the corrosion of the metallic (pot metal or aluminum) ice form and small corroded particles falling on the ice. The ice form looked like it was coated with teflon or a paint. this form needs to be metal so heati
Replaced the 8 year old icemaker.
Turned off power.
Did not need to turnoff water supply.
Removed the 1/4" hex head screw from the wire connector cover.
Removed the wire cover taking care to be careful with the thermister
temperature sensor which slides into a square channel in the cover.
Disconnected both wire connectors.
Unscrewed the 5/16" hex screw at bottom of icemaker to unmount the old icemaker, lift the icemaker up 1/2" and out and discard.
Installed new icemaker in reverse order.
Turned off power.
Did not need to turnoff water supply.
Removed the 1/4" hex head screw from the wire connector cover.
Removed the wire cover taking care to be careful with the thermister
temperature sensor which slides into a square channel in the cover.
Disconnected both wire connectors.
Unscrewed the 5/16" hex screw at bottom of icemaker to unmount the old icemaker, lift the icemaker up 1/2" and out and discard.
Installed new icemaker in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randall from coopersville, MI
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
refriderator not cooling consistetly
1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from SCOTTSDALE, AZ
- Parts Used:
- WR55X10025
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Defrost not working coil iced up
Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rickey from DUMAS, AR
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugged it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KYLE, TX
- Parts Used:
- WR71X11063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dairy bin did not come with the refrigerator
Slipped into place easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Therese from BONNERS FERRY, ID
- Parts Used:
- WR71X11046
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Dropped and broke the small bin in my refrigerator.
I ordered the correct part, the box said it was the correct part and when I opened the box a completely different part was inside. Not only was it the wrong part but it was loosely wrapped with very thin plastic and the hinge was broken off of the lid and laying in the box. I have called and emailed for help and was told no one was available to help because of COVID 19. One email was answered to return the part I would have to pay shipping and the part could not be damaged. Okay, the part was wrong, the part was broken. Now what should I do? Please respond.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from MESA, AZ
- Parts Used:
- WR01X11023, WR02X13630, WR02X13629
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Cross bar wasn't all there from a scratch n dent store
Purchased parts per your diagram and went to a appliance store to see how it was assemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheryl from SAINT LOUIS, MO
- Parts Used:
- RPWFE
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator water filter replacement.
I followed the directions included with the water filter and it was simple. The only problem I had was not being strong enough to easily remove the old filter. I did accomplish that after a few tries and the rest is history.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from GEORGETOWN, DE
- Parts Used:
- WR57X27487
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Would not dispense water or make ice.
Pull the fridge out from the wall.
Close the water supply valve.
Unplug the appliance.
Using a nutdriver , remove the panel at the lower rear. Set aside.
Disconnect the water supply line from the solenoid valve.
Using the nutdriver, remove the defective water valve.
Disconnect the electrical connector noting orientation.
Remove the black safety device from the valve where the quick connect line goes to the dispenser. Depress the ring on the fitting and remove the gray dispenser line.
Discard the defective valve.
Insert the dispenser line into the quick connect fitting on the new valve. Ensure that the line goes all the way into the fitting.
Reconnect the electrical connector.
Install the valve and connect the supply line.
Reinstall the panel.
Open the supply line valve.
Plug in the refrigerator.
Test. There well be some gurgling as water refills the system.
If no leaks and water dispenses properly, push the fridge back against the wall.
Enjoy!
Close the water supply valve.
Unplug the appliance.
Using a nutdriver , remove the panel at the lower rear. Set aside.
Disconnect the water supply line from the solenoid valve.
Using the nutdriver, remove the defective water valve.
Disconnect the electrical connector noting orientation.
Remove the black safety device from the valve where the quick connect line goes to the dispenser. Depress the ring on the fitting and remove the gray dispenser line.
Discard the defective valve.
Insert the dispenser line into the quick connect fitting on the new valve. Ensure that the line goes all the way into the fitting.
Reconnect the electrical connector.
Install the valve and connect the supply line.
Reinstall the panel.
Open the supply line valve.
Plug in the refrigerator.
Test. There well be some gurgling as water refills the system.
If no leaks and water dispenses properly, push the fridge back against the wall.
Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from HEBER, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
condenser icing refrigerator warm freezer ok
follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from OAK FOREST, IL
- Parts Used:
- WR71X11044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf on right Door Broke - Fell apart
Once I received that New Part, just place the 1 Piece from the old Shelf into the New Part and mounted the Shelf in the Door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elias from PARKER, CO
- Parts Used:
- WR55X30604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lights in the refrigerator were very dim
I determined one of the five LED lights in the refrigerator was dead by swapping it with a working one. The refrigerator lights are wired in series and if one of the lights is dead the remaining ones turn on, but very dim. I called PartSelect.com and thanks to their help we determined the correct part to order which is the oval-shaped cover LED assembly which includes the cover, LED, and female connector. The part from PartSelect arrived in three days. The oval-shape LED plastic Cover assembly is mounted on the refrigerator and held by a couple of side latches. First unplug the refrigerator and then proceed to lightly pry the oval-shaped cover side facing the rear of the refrigerator with your finger nail to remove it. With the LED cover removed you can then press on the LED connector tab to slide it off. Now slide the female connector of the replacement part to the refrigerator male connector and snap the oval-shape plastic cover onto the refrigerator receptacle and then plug it back to its outlet. Now all the lights in the refrigerator should light up brightly! That's all folks. Hope this helps. Good luck. Yours truly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from DURYEA, PA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
both freezer and refigerator were warm.
I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.
Was this instruction helpful to you?
Thank you for voting!