TBX18ZAXARWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Loren from EL PASO, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Glendale Heights, IL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Light would stay on when door closed
Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Keyport, NJ
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My wife forced the fruit drawer in and snapped the slide rail.
I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.
Was this instruction helpful to you?
Thank you for voting!
original parts broken (poor design)
Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.
Was this instruction helpful to you?
Thank you for voting!
broken slide rails
Basically I removed 4 screws holding the rails together, did a little cleaning of the existing parts that I would re-use and screwed the 4 screws back in and put it back into the fridge. Piece of cake. If I hadn't cleaned up the old parts it would have taken me 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauraine from Rocky Hill, CT
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
family member melted fan with hair dryer
Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nikki from Raleigh, NC
- Parts Used:
- WR17X2770
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I broke the left side slide rail while trying to clean out refridgerator
I had one of my guy friends do it for me. It took him less than 10 minutes, and probably would have been quicker if he had a better screw driver. Mine is a cheap girly one that he could not get a good grip on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Wingate, NC
- Parts Used:
- WR17X2770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer Slide Rails broken
The bottom shelf of my Mom's fridge broke. I found the part I needed and went to repair it. Realized both sides were broken. Ordered other side as well. Two screws in front, two screws in back. Front side had a metal strip covering screws. Had to pull that off to get to screws. Snapped back on after repair.
Mother was very pleased.
Told her to be careful. Those little pieces of plastic can be expensive.
Mother was very pleased.
Told her to be careful. Those little pieces of plastic can be expensive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from KEARNY, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light was flicking
It was way to ez to install only a couple of minutes that's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Cumberland, MD
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fan blade broken
Removed the broken fan blade (just pulled off) and replaced with part purchased PartSelect. Very easy repair, no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erika from Joliet, IL
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door shelf clip had broken
This shelf has been broken for about a year now and my husband tried several little quick fixes that would work for a while and then the shelf would fall again. A quick search online led me to your website, the part arrive within two days, and the shelf was fixed in less than ten minutes. It's working great. We'll definitely keep you in mind for the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from SANDWICH, IL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken light switch
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
The vegie draw rack cover
Both side rails were busted. the parts were precise and it was extremely easy. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- QUOC-LOC from LYNN HAVEN, FL
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The control board generated clicking noise. Temperature display wrong values.
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Odessa, FL
- Parts Used:
- WR72X273
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken slide rail
removed the screws and then replaced the rails. Easy
Was this instruction helpful to you?
Thank you for voting!