ZISS42DYASS General Electric Refrigerator - Instructions

Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great

Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!

Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) removed fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

Easy to take apart just keep track of all your screws and parts most inportant of all are the 3 claw like and spacers that are inside the clear round part at the end of the ice bucket these pieces only turn in one direction if you put them on backwards or in the wrong order you will tear up your ice bucket so pay close attention when taking it apart and reassembling it. One think that might be helpful is to take some pictures of the ice bucket before disassembly something i wish i had done prior to taking it apart. Some people download instructions off the internet but i felt like i could do it with out help well good luck

Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.

The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!

I removed the ice container with the auger inside. I removed the front panel, then the auger and housing. I had to clean all of the parts that had rust on them. I got some of the parts mixed up and was having a hard time putting them back where they belonged. I went back on the PartSelect web site and with my IPad and opened the exploded view of the parts. This enabled me to put the auger back together. It works perfectly now. Saved a lot of money by doing it myself. Thanks PartSelect.

replaced circuit board and water solenoids

I replaced tie ice Dispenser Plate & thye ice Bucket Auger.I read the previous installation instructions written on this website first.Good info! I copied the Parts diagram on the website, this really helped. I also took my phone camera and took pictures as I was taking the parts apart. The only problem I had was with the Wire Actuator Display Rod,making sure the spring tension was correct and positioned the correct way when I reassembled it. I was able to look at my pictures and assemble it back the correct way. I put the ice bucket assembly back in the refrig and it works great. No more rusty Ice!!!!!!!!!!!!!!

Watched the video from your site and followed instructions, extremely easy after that.

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.