GSG25IEMCFWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victor from Houston, TX
- Parts Used:
- WR17X23255
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Auger for the ice dispenser would not turn.
I replaced the ice tray with a new one. Could not tell what was broken in the tray, so I just purchased a new one, as the repair man service charge is 60.00 and then you have to pay for the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randall from coopersville, MI
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
refriderator not cooling consistetly
1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- doyle from kingston, WA
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
freezer was freezing up.
took the back off and defrosted with a hairdryer. disconected the part pulled the part out cut the wires. put the other part on and instaled it. put it back together and it seems to be working just fine. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shock Tech Electric from VICKSBURG, MI
- Parts Used:
- WR17X11168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Water leaking as it enters the frezer ice maker
Very easy novice could do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- IRISA from TAMPA, FL
- Parts Used:
- WR32X10834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken off side support
exchanged
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Springfield, IL
- Parts Used:
- WR17X11497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
plastic parts came out of ice dispenser
Removed icemaker from freezer, remove covers allowing access to dispenser. In the next step I removed the auger and broken shield as one assembly. With assembly out of icemaker it was a simple task of taking the broken shield off of auger and putting the new one on. Reassemble in reverse order as removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Interior Light did not go on due to faulty switch
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Holly Springs, NC
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Fridge getting warer and warmer
remove back panel inside fridge freezer side, everything frosted, unplug and used a hair dryer
1. Took out defrost heater and the bottom and tested (per this site) tested OK.
2. Then looked at the defrost thermostat, it was swollen with the top coming off. so i new it was bad
3.clipped and stripped the 2 wires, spliced in the new one with wire nuts and sealed them with silicone. All better
1. Took out defrost heater and the bottom and tested (per this site) tested OK.
2. Then looked at the defrost thermostat, it was swollen with the top coming off. so i new it was bad
3.clipped and stripped the 2 wires, spliced in the new one with wire nuts and sealed them with silicone. All better
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Orange, CA
- Parts Used:
- WR24X10053
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Evaperator continualy iced up causing the unit to not cool effectively
Removed the 28 -5/16" nuts that held the freezer door panel on and the rear panel that covered the evaporator.
once open the evaperator was defrosted (this took some time) and the interior of the freezer door was defrosted as well.
after defrosting, drying and cleaning, the gasket was simply pulled off and the new gasket was installed on the panel then reinstalled on the door (be sure to follow the instructions on the box that the gasket came in for removing any deformaties due to shipping).
Note that due to the age and loosness of the fasting screws I replaced the # 8 screws with new #10 screws.
once open the evaperator was defrosted (this took some time) and the interior of the freezer door was defrosted as well.
after defrosting, drying and cleaning, the gasket was simply pulled off and the new gasket was installed on the panel then reinstalled on the door (be sure to follow the instructions on the box that the gasket came in for removing any deformaties due to shipping).
Note that due to the age and loosness of the fasting screws I replaced the # 8 screws with new #10 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from HEBER, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
condenser icing refrigerator warm freezer ok
follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Highlands Ranch, CO
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dairy door broke
Put the new one in--simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Brighton, MI
- Parts Used:
- WR17X23255
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problem
Remove the ice dispenser bucket and auger assembly from box. Washed the assembly. Opened freezer door. Removed old assembly. Slid new assembly into place. End of problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Vacaville, CA
- Parts Used:
- WR62X10055, WR17X11653, WR17X23255, WR2X8818, WR17X10712, WR17X10706, WR02X10585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The icemaker door did not work and broke the ice maker
I replaced the door and soleniod and the other parts and it works great now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVE from LA VERNE, AL
- Parts Used:
- WR17X11497, WR17X23255
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken auger nut and crusher cover dispenser
1. Slide out that big box with all the ice in it
2. Remove two screws (phillips tipped)under white plastic cover,pull off the cover
3. Press the two plastic tabs in, to release white box thingy
4. Pull the box out, long plastic ice screwer and all
5. Notice how the stainless blades go back in before removing
6. This up to you, but at this point I took a break
7. Note: the auger nut is a left hand thread, it took me a while to figure that out (Porter?)
8. Screw on the new auger nut, I used a putty knife to span the screwdriver like slot, slide your new crusher cover on, slide assembly back into place, install snap ring
9. reassemble
10. Realize the real problem is the solenoid for the rubber flapper that is stuck open allowing the ice to frost and freeze and break the parts I just replaced
11. to be continued ():
2. Remove two screws (phillips tipped)under white plastic cover,pull off the cover
3. Press the two plastic tabs in, to release white box thingy
4. Pull the box out, long plastic ice screwer and all
5. Notice how the stainless blades go back in before removing
6. This up to you, but at this point I took a break
7. Note: the auger nut is a left hand thread, it took me a while to figure that out (Porter?)
8. Screw on the new auger nut, I used a putty knife to span the screwdriver like slot, slide your new crusher cover on, slide assembly back into place, install snap ring
9. reassemble
10. Realize the real problem is the solenoid for the rubber flapper that is stuck open allowing the ice to frost and freeze and break the parts I just replaced
11. to be continued ():
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!