GBS18HBPC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MARTIN from RIVER FALLS, WI
- Parts Used:
- WR09X10107
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Smelled electrical/plastic burning. Pulled out refrigerator and noticed small flame near compressor.
Unplugged refrigerator. Removed relay by unclipping wire and pulling relay off compressor. Looked-up part number and ordered part. Replaced part and plugged in refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from McKinney, TX
- Parts Used:
- WR60X10300
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Refrig would not cool, freezer worked fine
Barry G was right on with instructions and expectations of the process to trouble shoot parts and how to replace. Barry also provide the right part numbers for replacement items. Thanks again Barry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Boston, KY
- Parts Used:
- WR17X11168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broke ice maker supply tube while moving fridge.
Used nut driver to remove two screws at top of tube, and the three screws holding composite cover on back of fridge. Pulled out the upper portion of tube, pulled up on fitting and removed lower portion of tube. Put upper spout portion of new supply tube into position, replaced two screws, pushed lower portion of tube into locking fitting on supply valve solenoid. Replaced composite cover with three screws, and was done. Entire job took less than 5 minutes. It took longer for me to find my nut driver set, than it took to do the repair. I ordered the part online, and it was delivered to my door in a lightning fast 36 hours. Hopefully I won't ever need any more appliance parts, but with your easy to navigate website, fast shipping, and fair prices, you have won me over as a customer. I will refer you to friends because of your high speed, low drag, zero defects, excellent service. Thank you very much. Rich.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Oxford, MI
- Parts Used:
- WR60X10300
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
the new motor was slightly larger than the old one and the bracket does not fit
Had to get behind the refrigerator and clean the drain out first and that took at least and hour. Just unplug the old motor. Took the old parts of the old motor, put them on the new one and plugged it back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from San Antonio, TX
- Parts Used:
- WR17X11168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Leaking water from outside top right rear of ice maker tube
Turned off water supply, removed bottom rear metal panel,with a towel to catch water pushed in and removed water line from double water outlet, removed metal clamp and then grommet tube assembly from top right rear of refrigerator. Then I put in new grommet tube assembly, turned on my water and checked for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Oleg from Lees Summit, MO
- Parts Used:
- WR2X9295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Reistall shelf
Replaced cap and reinstalled. But I used iron nail inside cover to hold right side because crack was at right hole and right part would not help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Niagara Falls, NY
- Parts Used:
- WR2X9295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door shelf end cap broke off
easily popped the new one in.
Was this instruction helpful to you?
Thank you for voting!