GDS18SCPLS General Electric Refrigerator - Instructions

A friend had no problem getting the new ice maker in. But then the problems started. The ice maker works great. But when the water fills the ice maker it squirts water onto the side of the freezer and ice sickles form. So we watched and decided the hole was too large so used a piece of plastic. That helped to cover the hole. But some water is still entering the freezer and not all going to the ice maker. The only other thing we can think to try is to use epoxy to try to close that place. A simple job has turned into a big headache. I wish they made the ice maker like the original one.

The video on the site was very helpful. The repair was really easy. It was exactly the way the video showed how to do it. I would definitely use this site again to find parts, figure out the "how-to", and use for skematics of appliances. Thanks.

turn off water. turn off electricity. empty freezer section of frozen food. remove ice bucket. loosen two screws holding IM to wall of refrigerator. lift off icemaker, and then unplug it as you remove it. INSTALL new IM by: putting new water funnel onto new IM. attaching adapter cord to IM. plug in IM electrical cord to refrigerator and then hang the new IM onto the two loosened screws on the refrig wall. Now tighten the two screws. the extra adapter electrical cord hangs below the new IM, but does not get in the way when you reinstall old ice bucket. reload food, turn on elec and water. PS. i had a crack in the casing of the new IM, so i got a new one, but that one was cracked too. so i just installed the second cracked one. hope it is not a problem.

REplaced old icemaker with a new one. Install simple, However that was not the problem. I then replaced the water valve. Still no ice. I check the electric connection was OK. THe problem was the elbow fitting on the top back of the refrigerater leading to the icemaker was blocked with ice.Cleared it and turned water faucet up all the way. Ice maker worked.

The instruction video was great, mine was easy than even the video showed it to be. I changed it out in less than 15 minutes and it works great. The niocve things I didn't have to wait for a repairman or my husband to fix the problem.

I matched the part I needed throught your web site. Then I called and spoke to a customer support person, and gave my personal information to her. I do not like giving my credit card numbers over the internet. Your site allows me to do that.

Watched video on website then removed old ice maker. New one went in without any problems. Working great. I am a 60 year old woman and had never done anything like this but so easy. Husband scared now, doesn't know what project I will take on next.

install icemaker water was allways delivered to previous unit water is not being delivered to icemaker still having difficulty

I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just barely. But I'm back in the ice again, no dripping water, all is good.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

Installing the actual ice maker was quite easy. What takes most of the time is preparing the freezer for the install. Need to remove all shelving, (and the door) to gain access to the unit. The ice maker is simple to install once access is achieved. Putting everything back together takes some time.

It was exactly as shown in your instruction video

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

Water was leaking on the floor from under the fridge and I noticed that the cubes were very small and the ice maker was taking much too long to make ice. After pulling the fridge out from the wall, I removed the bottom back plate (about 7 screws) and checked the ice maker refill tube that goes from the inlet valve at the bottom of the fridge (left side) into the ice maker at the top right side of the fridge. The 1/4" tube had split 2 " from the inlet valve where it makes a sharp "U" turn on its' way up to the ice maker. I turned off the ice maker by raising the handle on the ice maker and turning off the 1/2" supply tube from the house supply pipe. I then tried splicing the tube by cutting it at the split and installing a 1/4" barbed splice on the two ends, but could not get a water tight connection. I then decided to order a new refill tube from Parts Select. The part arrived in 1 day (FANTASTIC SERVICE) and I installed it in about 10 minutes with no problem. (GE was out of stock on this part.) To begin, I disconnected the old tube at the water inlet valve (just push in the quick connect and then pull out) and proceeded to disconnect the other end at the top of the fridge where the ice maker is located. The molded end is adhered to the back with a sticky adhesive and must be scraped off with a putty knife before it can be pulled out. Once this is done, the new refill tube goes in the exact same way. One caution- just be sure to test and adjust the length of the white supply tube (I had to lengthen it by 1 ") before peeling the protective paper off the adhesive. It must be long enough to reach the white plastic cup that fills the ice maker. The inlet valve end of the 1/4" tube at the bottom just pushed into the quick connect connection. I then turned the ice maker back on inside the fridge by lowering the handle and also turned the house supply valve back on. I waited for the ice maker to call for water and then checked for leaks. NO LEAKS- job done!

Removed old ice maker, then screwed in new ice maker. Only thing that was a little difficult was to hold the auger motor, while trying to unplug the clipped in plug on the old ice maker. I could have used an extra pair of hands.